Differences between revisions 4 and 5
Revision 4 as of 2013-11-17 00:48:02
Size: 67556
Editor: ?jeka
Comment:
Revision 5 as of 2013-11-18 05:34:02
Size: 68864
Editor: ?jeka
Comment:
Deletions are marked like this. Additions are marked like this.
Line 32: Line 32:
 (note the mandatory preceding white space). There can be white space on either side of the =. Parameter names follow the same syntax as section names, and are specific to a section type. Unless otherwise explicitly specified, no parameter name may appear more than once in a section.(обратите внимание на обязательное присутствие символов пробел перед параметром). Пробелы могут присутствовать по обе стороны от знака равенства =. Имена параметров имеют тот же самый синтаксис что и названия разделов, также для каждого типа раздела имеется строго только свой набор различных параметров. Имя параметра не может быть объявлено более одного раза в разделе, если в руководстве об этом вам не сообщается явно.

  An empty value stands for the system default value (if any) of the parameter, i.e. it is roughly equivalent to omitting the parameter line entirely. A value may contain white space only if the entire value is enclosed in double quotes ("); a value cannot itself contain a double quote, nor may it be continued across more than one line.Пустое значение означает системное значение по умолчанию (если таковые имеются) параметра, т.е. это примерно равнозначно пропуску параметра строку целиком.Значение может содержать пробелов, только если вся стоимость заключена в двойные кавычки ("), значение не может сам содержать двойные кавычки, и оно не может быть продолжено в более чем одной строке.

 Numeric values are specified to be either an “integer” (a sequence of digits) or a “decimal number” (sequence of digits optionally followed by `.' and another sequence of digits).

  There is currently one parameter which is available in any type of section:
 (обратите внимание на обязательное присутствие символов пробел перед параметром). Пробелы могут присутствовать по обе стороны от знака равенства =. Имена параметров имеют тот же самый синтаксис что и названия разделов (то есть не должны содержать пробел в названии), также для каждого типа раздела имеется строго только свой набор различных параметров. Имя параметра не может быть объявлено более одного раза в разделе, если в руководстве об этом вам не сообщается явно.

  An empty value stands for the system default value (if any) of the parameter, i.e. it is roughly equivalent to omitting the parameter line entirely. A value may contain white space only if the entire value is enclosed in double quotes ("); a value cannot itself contain a double quote, nor may it be continued across more than one line.Пустое значение конкретного параметра указывает на системное значение по-умолчанию (если таковое имеется) у данного параметра, то есть это абсолютно равнозначно установке строки целиком в значение данного параметра. Значение может содержать символ пробела только в том случае, если все символы значения заключены в двойные кавычки - "значение параметра"; значение не может содержать внутри себя двойные кавычки, также установка значения обязана размещаться только в пределах одной строки.

 Числовые значения указываются либо в виде "целых" чисел (последовательность цифр) либо в виде "десятичных" чисел (последовательность цифр, в которой содержиться символ точки .)

  Следующий (единственный) параметр относится к любому типу разделов:
Line 41: Line 41:
 the value is a section name; the parameters of that section are appended to this section, as if they had been written as part of it. The specified section must exist, must follow the current one, and must have the same section type. (Nesting is permitted, and there may be more than one also in a single section, although it is forbidden to append the same section more than once.)  the value is a section name; the parameters of that section are appended to this section, as if they had been written as part of it. The specified section must exist, must follow the current one, and must have the same section type. (Nesting is permitted, and there may be more than one also in a single section, although it is forbidden to append the same section more than once.)Значение названия раздела; параметры этого раздела прилагаются к настоящему разделу, как если бы они были написаны как часть его. Указанная часть должна существовать, должны следовать текущей, и должны иметь одинаковый тип раздела. (Вложения разрешено, и там может быть больше чем один и в одной секции, хотя это запрещено добавлять том же разделе более одного раза.)
Line 43: Line 43:
   Это позволяет, например, хранение ключей шифрования для соединения в отдельном файле от остальной части описания, используя оба параметра, а также линии включают. (Внимание, см. ОШИБКИ ниже для некоторых ограничений.)

IPSEC.CONF(5) [FIXME: manual] IPSEC.CONF(5)

NAME

  • ipsec.conf - IPsec configuration and connections

DESCRIPTION

  • Файл "ipsec.conf", содержащий различные параметры, указывает основную часть информации о настройке и управлении для подсистемы Openswan IPsec. (Исключением является информация про пароли (секреты) для аутентификации; за более подробной информацией обратитесь к Ipsec.secrets (5)). Its contents are not security-sensitive unless manual keying is being done for more than just testing, in which case the encryption/authentication keys in the descriptions for the manually-keyed connections are very sensitive (and those connection descriptions are probably best kept in a separate file, via the include facility described below).
    • Файл "ipsec.conf" представляет собой обычный текстовый файл с чистым текстом внутри (plaintext), состоящий из одного или более разделов. Любые символы, следующие после символа решётки # и до конца строки представляют собой комментарий и игнорируются, точно также как и пустые строки, которые находятся за пределами определённых разделов.
    Строка, которая содержит "include имя_файла", заменяется на содержимое этого файла. Если имя файла содержит не полное имя, то имя файла считается относительным каталога, содержащего файл со строкой "include имя_файла", упомянутый выше. Подобные подключения внешних файлов могут быть вложенными. Только один файл может быть указан в "include", также имя_файла не должно содержать в себе пробелы, но может включать шаблоны shell (за более подробной информацией обратитесь к sh (1)), например:
    • include ipsec.*.conf
    • The intention of the include facility is mostly to permit keeping information on connections, or sets of connections, separate from the main configuration file. This permits such connection descriptions to be changed, copied to the other security gateways involved, etc., without having to constantly extract them from the configuration file and then insert them back into it. Note also the also and alsoflip parameters (described below) which permit splitting a single logical section (e.g. a connection description) into several actual sections.
    Это важно - в первой строке файла всегда необходимо указывать версию текущей спецификации, которой соответствует файл "ipsec.conf"
    • version 2
    Раздел начинается со строчки вида:
    • тип_раздела название_раздела
    где "тип_раздела" указывает, какой тип раздела следует дальше, и "название_раздела" - это произвольное имя, которое просто отличает конкретный раздел от других разделов одного и того же типа. (Имена разделов должны начинаться с буквы и могут содержать только буквы, цифры, точки, подчеркивания и дефис/тире/минус.) Все следующие далее непустые строки, имеющие отступ с символами пробела, являются частью текущего раздела; комментарии в разделе точно также должны начинаться с отступа пробельных символов. Присутствовать может только один раздел определённого типа под конкретным именем.
    • Строчки в разделе в основном имеют следующий вид
      • параметр=значение
    (обратите внимание на обязательное присутствие символов пробел перед параметром). Пробелы могут присутствовать по обе стороны от знака равенства =. Имена параметров имеют тот же самый синтаксис что и названия разделов (то есть не должны содержать пробел в названии), также для каждого типа раздела имеется строго только свой набор различных параметров. Имя параметра не может быть объявлено более одного раза в разделе, если в руководстве об этом вам не сообщается явно.
    • An empty value stands for the system default value (if any) of the parameter, i.e. it is roughly equivalent to omitting the parameter line entirely. A value may contain white space only if the entire value is enclosed in double quotes ("); a value cannot itself contain a double quote, nor may it be continued across more than one line.Пустое значение конкретного параметра указывает на системное значение по-умолчанию (если таковое имеется) у данного параметра, то есть это абсолютно равнозначно установке строки целиком в значение данного параметра. Значение может содержать символ пробела только в том случае, если все символы значения заключены в двойные кавычки - "значение параметра"; значение не может содержать внутри себя двойные кавычки, также установка значения обязана размещаться только в пределах одной строки.
    Числовые значения указываются либо в виде "целых" чисел (последовательность цифр) либо в виде "десятичных" чисел (последовательность цифр, в которой содержиться символ точки .)
    • Следующий (единственный) параметр относится к любому типу разделов:
      • also
    the value is a section name; the parameters of that section are appended to this section, as if they had been written as part of it. The specified section must exist, must follow the current one, and must have the same section type. (Nesting is permitted, and there may be more than one also in a single section, although it is forbidden to append the same section more than once.)Значение названия раздела; параметры этого раздела прилагаются к настоящему разделу, как если бы они были написаны как часть его. Указанная часть должна существовать, должны следовать текущей, и должны иметь одинаковый тип раздела. (Вложения разрешено, и там может быть больше чем один и в одной секции, хотя это запрещено добавлять том же разделе более одного раза.)
    • This allows, for example, keeping the encryption keys for a connection in a separate file from the rest of the description, by using both an also parameter and an include line. (Caution, see BUGS below for some restrictions.)
      • Это позволяет, например, хранение ключей шифрования для соединения в отдельном файле от остальной части описания, используя оба параметра, а также линии включают. (Внимание, см. ОШИБКИ ниже для некоторых ограничений.)
        • alsoflip
          • can be used in a conn section. It acts like an also that flips the referenced section's entries left-for-right.
          Parameter names beginning with x- (or X-, or x_, or X_) are reserved for user extensions and will never be assigned meanings by IPsec. Parameters with such names must still observe the syntax rules (limits on characters used in the name; no white space in a non-quoted value; no newlines or double quotes within the value). All other as-yet-unused parameter names are reserved for future IPsec improvements. A section with name %default specifies defaults for sections of the same type. For each parameter in it, any section of that type which does not have a parameter of the same name gets a copy of the one from the %default section. There may be multiple %default sections of a given type, but only one default may be supplied for any specific parameter name, and all %default sections of a given type must precede all non-%default sections of that type. %default sections may not contain also or alsoflip parameters. Currently there are two types of section: a config section specifies general configuration information for IPsec, while a conn section specifies an IPsec connection.

CONN SECTIONS

  • A conn section contains a connection specification, defining a network connection to be made using IPsec. The name given is arbitrary, and is used to identify the connection to ipsec_auto(8) and ipsec_manual(8). Here's a simple example:
    • conn snt
      • left=10.11.11.1 leftsubnet=10.0.1.0/24 leftnexthop=172.16.55.66 leftsourceip=10.0.1.1 right=192.168.22.1 rightsubnet=10.0.2.0/24 rightnexthop=172.16.88.99 rightsourceip=10.0.2.1 keyingtries=%forever
    A note on terminology... In automatic keying, there are two kinds of communications going on: transmission of user IP packets, and gateway-to-gateway negotiations for keying, rekeying, and general control. The data path (a set of “IPsec SAs”) used for user packets is herein referred to as the “connection”; the path used for negotiations (built with “ISAKMP SAs”) is referred to as the “keying channel”. To avoid trivial editing of the configuration file to suit it to each system involved in a connection, connection specifications are written in terms of left and right participants, rather than in terms of local and remote. Which participant is considered left or right is arbitrary; IPsec figures out which one it is being run on based on internal information. This permits using identical connection specifications on both ends. There are cases where there is no symmetry; a good convention is to use left for the local side and right for the remote side (the first letters are a good mnemonic). Many of the parameters relate to one participant or the other; only the ones for left are listed here, but every parameter whose name begins with left has a right counterpart, whose description is the same but with left and right reversed. Parameters are optional unless marked “(required)”; a parameter required for manual keying need not be included for a connection which will use only automatic keying, and vice versa.
  • CONN PARAMETERS: GENERAL
    • The following parameters are relevant to both automatic and manual keying. Unless otherwise noted, for a connection to work, in general it is necessary for the two ends to agree exactly on the values of these parameters. connaddrfamily
      • the connection addrress family of the connection; currently the accepted values are ipv4 (the default); or ipv6. This option is confusing, especially when doing IPv4-in-IPv6 or IPv6-in-IPv4 tunnels. The developers hope to remove this option in the near future for proper auto-detection. For now, set connaddrfamily= to the family of the *subnet= options, and if those are not defined, to the family of the left=/right= options. IPv6 is supported with NETKEY since openswan 2.4 and with KLIPS since Openswan 2.6.33
      type
      • the type of the connection; currently the accepted values are tunnel (the default) signifying a host-to-host, host-to-subnet, or subnet-to-subnet tunnel; transport, signifying host-to-host transport mode; passthrough, signifying that no IPsec processing should be done at all; drop, signifying that packets should be discarded; and reject, signifying that packets should be discarded and a diagnostic ICMP returned.
      left
      • (required) the IP address of the left participant's public-network interface, in any form accepted by ipsec_ttoaddr(3). Currently, IPv4 and IPv6 IP addresses are supported. There are several magic values. If it is %defaultroute, and the config setup section's, interfaces specification contains %defaultroute, left will be filled in automatically with the local address of the default-route interface (as determined at IPsec startup time); this also overrides any value supplied for leftnexthop. (Either left or right may be %defaultroute, but not both.) The value %any signifies an address to be filled in (by automatic keying) during negotiation. The value %opportunistic signifies that both left and leftnexthop are to be filled in (by automatic keying) from DNS data for left's client. The value can also contain the interface name, which will then later be used to obtain the IP address from to fill in. For example %ppp0 The values %group and %opportunisticgroup makes this a policy group conn: one that will be instantiated into a regular or opportunistic conn for each CIDR block listed in the policy group file with the same name as the conn. If using IP addresses in combination with NAT, always use the actual local machine's (NAT'ed) IP address, and if the remote (eg right=) is NAT'ed as well, the remote's public (not NAT'ed) IP address. Note that this makes the configuration no longer symmetrical on both sides, so you cannot use an identical configuration file on both hosts.
      leftsubnet
      • private subnet behind the left participant, expressed as network/netmask (actually, any form acceptable to ipsec_ttosubnet(3)); Currentlly, IPv4 and IPv6 ranges are supported. if omitted, essentially assumed to be left/32, signifying that the left end of the connection goes to the left participant only It supports two magic shorthands vhost: and vnet:, which can list subnets in the same syntax as virtual_private. The value %priv expands to the networks specified in virtual_private. The value %no means no subnet. A common use for allowing roadwarrios to come in on public IPs or via accepted NATed networks from RFC1918 is to use leftsubnet=vhost:%no,%priv. The vnet: option can be used to allow RFC1918 subnets without hardcoding them. When using vnet the connection will instantiate, allowing for multiple tunnels with different subnets.
      leftsubnets
      • specify multiple private subnets behind the left participant, expressed as { networkA/netmaskA networkB/netmaskB [...] } If both a leftsubnets= and rightsubnets= is defined, all combinations of subnet tunnels will be instantiated. You cannot use leftsubnet and leftsubnets together. For examples see testing/pluto/multinet-*.
      leftprotoport
      • allowed protocols and ports over connection, also called Port Selectors. The argument is in the form protocol, which can be a number or a name that will be looked up in /etc/protocols, such as leftprotoport=icmp, or in the form of protocol/port, such as tcp/smtp. Ports can be defined as a number (eg. 25) or as a name (eg smtp) which will be looked up in /etc/services. A special keyword %any can be used to allow all ports of a certain protocol. The most common use of this option is for L2TP connections to only allow l2tp packets (UDP port 1701), eg: leftprotoport=17/1701. Some clients, notably older Windows XP and some Mac OSX clients, use a random high port as source port. In those cases rightprotoport=17/%any can be used to allow all UDP traffic on the connection. Note that this option is part of the proposal, so it cannot be arbitrarily left out if one end does not care about the traffic selection over this connection - both peers have to agree. The Port Selectors show up in the output of ipsec eroute and ipsec auto --status eg:"l2tp": 193.110.157.131[@aivd.xelernace.com]:7/1701...%any:17/1701 This option only filters outbound traffic. Inbound traffic selection must still be based on firewall rules activated by an updown script. The variablees $PLUTO_MY_PROTOCOL, $PLUTO_PEER_PROTOCOL, $PLUTO_MY_PORT, and $PLUTO_PEER_PORT are available for use in updown scripts. Older workarounds for bugs involved a setting of 17/0 to denote any single UDP port (not UDP port 0). Some clients, most notably OSX, uses a random high port, instead of port 1701 for L2TP.
      leftnexthop
      • next-hop gateway IP address for the left participant's connection to the public network; defaults to %direct (meaning right). If the value is to be overridden by the left=%defaultroute method (see above), an explicit value must not be given. If that method is not being used, but leftnexthop is %defaultroute, and interfaces=%defaultroute is used in the config setup section, the next-hop gateway address of the default-route interface will be used. The magic value %direct signifies a value to be filled in (by automatic keying) with the peer's address. Relevant only locally, other end need not agree on it.
      leftsourceip
      • the IP address for this host to use when transmitting a packet to the other side of this link. Relevant only locally, the other end need not agree. This option is used to make the gateway itself use its internal IP, which is part of the leftsubnet, to communicate to the rightsubnet or right. Otherwise, it will use its nearest IP address, which is its public IP address. This option is mostly used when defining subnet-subnet connections, so that the gateways can talk to each other and the subnet at the other end, without the need to build additional host-subnet, subnet-host and host-host tunnels. Both IPv4 and IPv6 addresses are supported.
      leftupdown
      • what “updown” script to run to adjust routing and/or firewalling when the status of the connection changes (default ipsec _updown). May include positional parameters separated by white space (although this requires enclosing the whole string in quotes); including shell metacharacters is unwise. An example to enable routing when using the NETKEY stack, one can use: leftupdown="ipsec _updown --route yes" See ipsec_pluto(8) for details. Relevant only locally, other end need not agree on it.
      leftfirewall
      • This option is obsolete and should not used anymore.
      If one or both security gateways are doing forwarding firewalling (possibly including masquerading), and this is specified using the firewall parameters, tunnels established with IPsec are exempted from it so that packets can flow unchanged through the tunnels. (This means that all subnets connected in this manner must have distinct, non-overlapping subnet address blocks.) This is done by the default updown script (see ipsec_pluto(8)). The implementation of this makes certain assumptions about firewall setup, and the availability of the Linux Advanced Routing tools. In situations calling for more control, it may be preferable for the user to supply his own updown script, which makes the appropriate adjustments for his system.
    CONN PARAMETERS: AUTOMATIC KEYING
    • The following parameters are relevant only to automatic keying, and are ignored in manual keying. Unless otherwise noted, for a connection to work, in general it is necessary for the two ends to agree exactly on the values of these parameters. auto
      • what operation, if any, should be done automatically at IPsec startup; currently-accepted values are add (signifying an ipsec auto --add), route (signifying that plus an ipsec auto --route), start (signifying that plus an ipsec auto --up), manual (signifying an ipsec manual --up), and ignore (also the default) (signifying no automatic startup operation). See the config setup discussion below. Relevant only locally, other end need not agree on it (but in general, for an intended-to-be-permanent connection, both ends should use auto=start to ensure that any reboot causes immediate renegotiation).
      authby
      • how the two security gateways should authenticate each other; acceptable values are secret for shared secrets, rsasig for RSA digital signatures (the default), secret|rsasig for either, and never if negotiation is never to be attempted or accepted (useful for shunt-only conns). Digital signatures are superior in every way to shared secrets.
      ike
      • IKE encryption/authentication algorithm to be used for the connection (phase 1 aka ISAKMP SA). The format is "cipher-hash;modpgroup, cipher-hash;modpgroup, ..." Any left out option will be filled in with all allowed default options. Multiple proposals are separated by a comma. If an ike= line is specified, no other received proposals will be accepted. Formerly there was a distinction (by using a "!" symbol) between "strict mode" or not. That mode has been obsoleted. If an ike= option is specified, the mode is always strict, meaning no other received proposals will be accepted. Some examples are ike=3des-sha1,aes-sha1, ike=aes, ike=aes128-md5;modp2048, ike=aes128-sha1;dh22, ike=3des-md5;modp1024,aes-sha1;modp1536 or ike=modp1536. The options must be suitable as a value of ipsec_spi(8)'s --ike option. The default is to use IKE, and to allow all combinations of:
        • cipher: 3des or aes hash: sha1 or md5 pfsgroup (DHgroup): modp1024 or modp1536
        If Openswan was compiled with extra INSECURE and BROKEN options, then the des (1des) and null cipher, as well as modp768 are available. This turns your VPN into a joke. Do not enable these options. If openswan was compiled with USE_MODP_RFC5114 support, then Diffie-Hellman groups 22, 23 and 24 are also implemented as per RFC-5114. Instead of the modp key syntax, use the "dh" keyword, for example ike=3des-sha1;dh23
      phase2
      • Sets the type of SA that will be produced. Valid options are: esp for encryption (the default), and ah for authentication only.
      phase2alg
      • Specifies the algorithms that will be offered/accepted for a phase2 negotiation. If not specified, a secure set of defaults will be used. Sets are separated using comma's. The default values are the same as for ike= Note also that not all ciphers available to the kernel (eg through CryptoAPI) are necessarilly supported here. The format for ESP is ENC-AUTH followed by an optional PFSgroup. For instance, "3des-md5" or "aes256-sha1;modp2048" or "aes-sha1,aes-md5". For RFC-5114 DH groups, use the "dh" keyword, eg "aes256-sha1;dh23" The format for AH is AUTH followed by an optional PFSgroup. For instance, "md5" or "sha1;modp1536". A special case is AES CCM, which uses the syntax of "phase2alg=aes_ccm_a-152-null"
      esp
      • This option is obsolete. Please use phase2alg instead.
      ah
      • AH authentication algorithm to be used for the connection, e.g here. hmac-md5 The options must be suitable as a value of ipsec_spi(8)'s --ah option. The default is not to use AH. If for some (invalid) reason you still think you need AH, please use esp with the null encryption cipher instead. Note also that not all ciphers available to the kernel (eg through CryptoAPI) are necessarilly supported here.
      ikev2
      • IKEv2 (RFC4309) settings to be used. Currently the accepted values are permit, (the default) signifying no IKEv2 should be transmitted, but will be accepted if the other ends initiates to us with IKEv2; never or no signifying no IKEv2 negotiation should be transmitted or accepted; propose or yes signifying that we permit IKEv2, and also use it as the default to initiate; insist, signifying we only accept and receive IKEv2 - IKEv1 negotiations will be rejected. If the ikev2= setting is set to permit or propose, Openswan will try and detect a "bid down" attack from IKEv2 to IKEv1. Since there is no standard for transmitting the IKEv2 capability with IKEv1, Openswan uses a special Vendor ID "CAN-IKEv2". If a fall back from IKEv2 to IKEv1 was detected, and the IKEv1 negotiation contains Vendor ID "CAN-IKEv2", Openswan will immediately attempt and IKEv2 rekey and refuse to use the IKEv1 connection. With an ikev2= setting of insist, no IKEv1 negotiation is allowed, and no bid down attack is possible.
      sareftrack
      • Set the method of tracking reply packets with SArefs when using an SAref compatible stack. Currently only the mast stack supports this. Acceptable values are yes (the default), no or conntrack. This option is ignored when SArefs are not supported. This option is passed as PLUTO_SAREF_TRACKING to the updown script which makes the actual decisions whether to perform any iptables/ip_conntrack manipulation. A value of yes means that an IPSEC mangle table will be created. This table will be used to match reply packets. A value of conntrack means that additionally, subsequent packets using this connection will be marked as well, reducing the lookups needed to find the proper SAref by using the ip_conntrack state. A value of no means no IPSEC mangle table is created, and SAref tracking is left to a third-party (kernel) module. In case of a third party module, the SArefs can be relayed using the HAVE_STATSD deamon.
      leftid
      • how the left participant should be identified for authentication; defaults to left. Can be an IP address (in any ipsec_ttoaddr(3) syntax) or a fully-qualified domain name preceded by @ (which is used as a literal string and not resolved). The magic value %fromcert causes the ID to be set to a DN taken from a certificate that is loaded. Prior to 2.5.16, this was the default if a certificate was specified. The magic value %none sets the ID to no ID. This is included for completeness, as the ID may have been set in the default conn, and one wishes for it to default instead of being explicitly set. The magic value %myid stands for the current setting of myid. This is set in config setup or by ipsec_whack(8)), or, if not set, it is the IP address in %defaultroute (if that is supported by a TXT record in its reverse domain), or otherwise it is the system's hostname (if that is supported by a TXT record in its forward domain), or otherwise it is undefined.
      leftrsasigkey
      • the left participant's public key for RSA signature authentication, in RFC 2537 format using ipsec_ttodata(3) encoding. The magic value %none means the same as not specifying a value (useful to override a default). The value %dnsondemand (the default) means the key is to be fetched from DNS at the time it is needed. The value %dnsonload means the key is to be fetched from DNS at the time the connection description is read from ipsec.conf; currently this will be treated as %none if right=%any or right=%opportunistic. The value %dns is currently treated as %dnsonload but will change to %dnsondemand in the future. The identity used for the left participant must be a specific host, not %any or another magic value. The value %cert will load the information required from a certificate defined in %leftcert and automatically define leftid for you. Caution: if two connection descriptions specify different public keys for the same leftid, confusion and madness will ensue.
      leftrsasigkey2
      • if present, a second public key. Either key can authenticate the signature, allowing for key rollover.
      leftcert
      • If you are using leftrsasigkey=%cert this defines the certificate you would like to use. It should point to a X.509 encoded certificate file. If you do not specify a full pathname, by default it will look in /etc/ipsec.d/certs. If openswan has been compiled with USE_LIBNSS=true, then openswan will also check the NSS database for RSA keys. These can be software or hardware.
      leftca
      • specifies the authorized Certificate Authority (CA) that signed the certificate of the peer. If undefined, it defaults to the CA that signed the certificate specified in leftcert. The special rightca=%same is implied when not specifying a rightca and means that only peers with certificates signed by the same CA as the leftca will be allowed. This option is only useful in complex multi CA certificate situations. When using a single CA, it can be safely omitted for both left and right.
      leftsendcert
      • This option configures when Openswan will send X.509 certificates to the remote host. Acceptable values are yes|always (signifying that we should always send a certificate), ifasked (signifying that we should send a certificate if the remote end asks for it), and no|never (signifying that we will never send a X.509 certificate). The default for this option is ifasked

        which may break compatibility with other vendor's IPSec implementations, such as Cisco and ?SafeNet. If you find that you are getting errors about no ID/Key found, you likely need to set this to always. This per-conn option replaces the obsolete global nocrsend option.

      leftxauthserver
      • Left is an XAUTH server. This can use PAM for authentication or md5 passwords in /etc/ipsec.d/passwd. These are additional credentials to verify the user identity, and should not be confused with the XAUTH group secret, which is just a regular PSK defined in ipsec.secrets. The other side of the connection should be configured as rightxauthclient. XAUTH connections cannot rekey, so rekey=no should be specified in this conn. For further details on how to compile and use XAUTH, see README.XAUTH. Acceptable values are yes or no (the default).
      leftxauthclient
      • Left is an XAUTH client. The xauth connection will have to be started interactively and cannot be configured using auto=start. Instead, it has to be started from the commandline using ipsec auto --up connname. You will then be prompted for the username and password. To setup an XAUTH connection non-interactively, which defeats the whole purpose of XAUTH, but is regularly requested by users, it is possible to use a whack command - ipsec whack --name baduser --ipsecgroup-xauth --xauthname badusername --xauthpass password --initiate The other side of the connection should be configured as rightxauthserver. Acceptable values are yes or no (the default).
      leftxauthusername
      • The XAUTH username associated with this XAUTH connection. The XAUTH password can be configured in the ipsec.secrets file.
      leftmodecfgserver
      • Left is a Mode Config server. It can push network configuration to the client. Acceptable values are yes or no (the default).
      leftmodecfgclient
      • Left is a Mode Config client. It can receive network configuration from the server. Acceptable values are yes or no (the default).
      modecfgpull
      • Pull the Mode Config network information from the server. Acceptable values are yes or no (the default).
      modecfgdns1, modecfgdns2, modecfgwins1, modecfgwins2
      • Specify the IP address for DNS or WINS servers for the client to use.
      remote_peer_type
      • Set the remote peer type. This can enable additional processing during the IKE negotiation. Acceptable values are cisco or ietf (the default). When set to cisco, support for Cisco IPsec gateway redirection and Cisco obtained DNS and domainname are enabled. This includes automatically updating (and restoring) /etc/resolv.conf. These options require that XAUTH is also enabled on this connection.
      nm_configured
      • Mark this connection as controlled by Network Manager. Acceptable values are yes or no (the default). Currently, setting this to yes will cause openswan to skip reconfiguring resolv.conf

        when used with XAUTH and ?ModeConfig.

      forceencaps
      • In some cases, for example when ESP packets are filtered or when a broken IPsec peer does not properly recognise NAT, it can be useful to force RFC-3948 encapsulation. forceencaps=yes forces the NAT detection code to lie and tell the remote peer that RFC-3948 encapsulation (ESP in UDP port 4500 packets) is required. For this option to have any effect, the setup section option nat_traversal=yes needs to be set. Acceptable values are yes or no (the default).
      overlapip
      • a boolean (yes/no) that determines, when *subnet=vhost: is used, if the virtual IP claimed by this states created from this connection can with states created from other connections. Note that connection instances created by the Opportunistic Encryption or PKIX (x.509) instantiation system are distinct internally. They will inherit this policy bit. The default is no. This feature is only available with kernel drivers that support SAs to overlapping conns. At present only the (klips)mast protocol stack supports this feature.
      dpddelay
      • Set the delay (in seconds) between Dead Peer Dectection (RFC 3706) keepalives (R_U_THERE, R_U_THERE_ACK) that are sent for this connection (default 30 seconds). If dpddelay is set, dpdtimeout also needs to be set.
      dpdtimeout
      • Set the length of time (in seconds) we will idle without hearing either an R_U_THERE poll from our peer, or an R_U_THERE_ACK reply. After this period has elapsed with no response and no traffic, we will declare the peer dead, and remove the SA (default 120 seconds). If dpdtimeout is set, dpdaction also needs to be set.
      dpdaction
      • When a DPD enabled peer is declared dead, what action should be taken. hold (default) means the eroute will be put into %hold status, while clear means the eroute and SA with both be cleared. restart means the the SA will immediately be renegotiated, and restart_by_peer means that ALL SA's to the dead peer will renegotiated. dpdaction=clear is really only useful on the server of a Road Warrior config.
      pfs
      • whether Perfect Forward Secrecy of keys is desired on the connection's keying channel (with PFS, penetration of the key-exchange protocol does not compromise keys negotiated earlier); Since there is no reason to ever refuse PFS, Openswan will allow a connection defined with pfs=no to use PFS anyway. Acceptable values are yes (the default) and no.
      pfsgroup
      • This option is obsoleted, please use phase2alg if you need the pfs to be different from phase1 (the default) using: phase2alg=aes128-md5;modp1024
      aggrmode
      • Use Aggressive Mode instead of Main Mode. Aggressive Mode is less secure, and vulnerable to Denial Of Service attacks. It is also vulnerable to brute force attacks with software such as ikecrack. It should not be used, and it should especially not be used with XAUTH and group secrets (PSK). If the remote system administrator insists on staying irresponsible, enable this option. Aggressive Mode is further limited to only proposals with one DH group as there is no room to negotiate the DH group. Therefor it is mandatory for Aggressive Mode connections that both ike= and phase2alg= options are specified with only fully specified proposal using one DH group. Acceptable values are yes or no (the default). The ISAKMP SA is created in exchange 1 in aggressive mode. Openswan has to send the exponent during that exchange, so it has to know what DH group to use before starting. This is why you can not have multiple DH groups in aggressive mode. In IKEv2, which uses a similar method to IKEv1 Aggressive Mode, there is a message to convey the DH group is wrong, and so an IKEv2 connection can actually recover from picking the wrong DH group by restarting its negotiation.
      salifetime
      • how long a particular instance of a connection (a set of encryption/authentication keys for user packets) should last, from successful negotiation to expiry; acceptable values are an integer optionally followed by s (a time in seconds) or a decimal number followed by m, h, or d (a time in minutes, hours, or days respectively) (default 8h, maximum 24h). Normally, the connection is renegotiated (via the keying channel) before it expires. The two ends need not exactly agree on salifetime, although if they do not, there will be some clutter of superseded connections on the end which thinks the lifetime is longer. The keywords "keylife" and "lifetime" are aliases for "salifetime."
      rekey
      • whether a connection should be renegotiated when it is about to expire; acceptable values are yes (the default) and no. The two ends need not agree, but while a value of no prevents Pluto from requesting renegotiation, it does not prevent responding to renegotiation requested from the other end, so no will be largely ineffective unless both ends agree on it.
      rekeymargin
      • how long before connection expiry or keying-channel expiry should attempts to negotiate a replacement begin; acceptable values as for salifetime (default 9m). Relevant only locally, other end need not agree on it.
      rekeyfuzz
      • maximum percentage by which rekeymargin should be randomly increased to randomize rekeying intervals (important for hosts with many connections); acceptable values are an integer, which may exceed 100, followed by a `%' (default set by ipsec_pluto(8), currently 100%). The value of rekeymargin, after this random increase, must not exceed salifetime. The value 0% will suppress time randomization. Relevant only locally, other end need not agree on it.
      keyingtries
      • how many attempts (a whole number or %forever) should be made to negotiate a connection, or a replacement for one, before giving up (default %forever). The value %forever means “never give up” (obsolete: this can be written 0). Relevant only locally, other end need not agree on it.
      ikelifetime
      • how long the keying channel of a connection (buzzphrase: “ISAKMP SA”) should last before being renegotiated; acceptable values as for keylife (default set by ipsec_pluto(8), currently 1h, maximum 24h). The two-ends-disagree case is similar to that of keylife.
      compress
      • whether IPComp compression of content is proposed on the connection (link-level compression does not work on encrypted data, so to be effective, compression must be done before encryption); acceptable values are yes and no (the default). The two ends need not agree. A value of yes causes IPsec to propose both compressed and uncompressed, and prefer compressed. A value of no prevents IPsec from proposing compression; a proposal to compress will still be accepted.
      metric
      • Set the metric for the routes to the ipsecX or mastX interface. This makes it possible to do host failover from another interface to ipsec using route management. This value is passed to the _updown scripts as PLUTO_METRIC. This option is only available with KLIPS or MAST on Linux. Acceptable values are positive numbers, with the default being 1.
      mtu
      • Set the mtu for the route(s) to the remote endpoint and/or subnets. This is sometimes required when the overhead of the IPsec encapsultion would cause the packet the become too big for a router on the path. Since IPsec cannot trust any unauthenticated ICMP messages, PATH MTU discovery does not work. This can also be needed when using "6to4" IPV6 deployments, which adds another header on the packet size. Acceptable values are positive numbers. There is no default.
      disablearrivalcheck
      • whether KLIPS's normal tunnel-exit check (that a packet emerging from a tunnel has plausible addresses in its header) should be disabled; acceptable values are yes and no (the default). Tunnel-exit checks improve security and do not break any normal configuration. Relevant only locally, other end need not agree on it.
      failureshunt
      • what to do with packets when negotiation fails. The default is none: no shunt; passthrough, drop, and reject have the obvious meanings.
    CONN PARAMETERS: MANUAL KEYING
    • This command was obsoleted around the same time that Al Gore invented the internet. ipsec manual was used in the jurassic period to load static keys into the kernel. There are no rational reasons to use this, and it is not supported anymore. If you need to create static SAs, then you can use ipsec spi and ipsec eroute when using KLIPS or ip xfrm or setkey when using NETKEY. No rational person uses static keys. They are not easier to use. REPEAT: they are not easier to use.

CONFIG SECTIONS

  • At present, the only config section known to the IPsec software is the one named setup, which contains information used when the software is being started (see ipsec_setup(8)). Here's an example:
    • config setup
      • interfaces="ipsec0=eth1 ipsec1=ppp0" klipsdebug=none plutodebug=control protostack=auto manualstart=
    Parameters are optional unless marked “(required)”. The currently-accepted parameter names in a config setup section are: myid
    • the identity to be used for %myid. %myid is used in the implicit policy group conns and can be used as an identity in explicit conns. If unspecified, %myid is set to the IP address in %defaultroute (if that is supported by a TXT record in its reverse domain), or otherwise the system's hostname (if that is supported by a TXT record in its forward domain), or otherwise it

      is undefined. An explicit value generally starts with @.

    protostack
    • decide which protocol stack is going to be used. Valid values are "auto", "klips", "netkey" and "mast". The "mast" stack is a variation for the klips stack.
    interfaces
    • virtual and physical interfaces for IPsec to use: a single virtual=physical pair, a (quoted!) list of pairs separated by white space, or %none. One of the pairs may be written as

      %defaultroute, which means: find the interface d that the default route points to, and then act as if the value was ipsec0=d. %defaultroute is the default; %none must be used to denote no interfaces, or when using the NETKEY stack. If %defaultroute is used (implicitly or explicitly) information about the default route and its interface is noted for use by ipsec_manual(8) and ipsec_auto(8).)

    listen
    • IP address to listen on (default depends on interfaces= setting). Currently only accepts one IP address.
    nat_traversal
    • whether to accept/offer to support NAT (NAPT, also known as "IP Masqurade") workaround for IPsec. Acceptable values are: yes and no (the default). This parameter may eventually become per-connection.
    disable_port_floating
    • whether to enable the newer NAT-T standards for port floating. Acceptable values are no (the default) and yes .
    force_keepalive
    • whether to force sending NAT-T keep-alives to support NAT which are send to prevent the NAT router from closing its port when there is not enough traffic on the IPsec connection. Acceptable values are: yes and no (the default). This parameter may eventually become per-connection.
    keep_alive
    • The delay (in seconds) for NAT-T keep-alive packets, if these are enabled using force_keepalive This parameter may eventually become per-connection.
    virtual_private
    • contains the networks that are allowed as subnet= for the remote clients when using the vhost: or vnet: keywords in the subnet= parameters. In other words, the address ranges that may live behind a NAT router through which a client connects. This value is usually set to all the RFC-1918 address space, excluding the space used in the local subnet behind the NAT (An IP address cannot live at two places at once). IPv4 address ranges are denoted as %v4:a.b.c.d/mm and IPv6 is denoted as %v6:aaaa::bbbb:cccc:dddd:eeee/mm. One can exclude subnets by using the !. For example, if the VPN server is giving access to 192.168.1.0/24, this option should be set to: virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!192.168.1.0/24. This parameter is only needed on the server side and not on the client side that resides behind the NAT router, as the client will just use its IP address for the inner IP setting. This parameter may eventually become per-connection. See also leftsubnet= Note: It seems that T-Mobile in the US and Rogers/Fido in Canada have started using 25.0.0.0/8 as their pre-NAT range. This range technically belows to the Defence Interoperable Network Services Authority (DINSA), an agency of the Ministry of Defence of the United Kingdom. The network range seems to not have been announced for decades, which is probably why these organisasions "borrowed" this range. To support roadwarriors on these 3G networks, you might have to add it to the virtual_private= line.
    oe
    • a boolean (yes/no) that determines if Opportunistic Encryption will be enabled. Opportunistic Encryption is the term to describe using IPsec tunnels without prearrangement. It uses IPSECKEY or TXT records to announce public RSA keys for certain IP's or identities. For a complete description see /doc/draft-richardson-ipsec-opportunistic.txt, doc/opportunism-spec.txt and doc/opportunism.howto. See also the IETF BTNS working group and RFC4025. The default is no. This feature is only available with kernel drivers that support the caching of packets (%hold eroutes or equivalent) that allows us to respond to a packet from an unknown IP address. At present only the (klips)mast protocol stack supports this feature.
    nhelpers
    • how many pluto helpers are started to help with cryptographic operations. Pluto will start (n-1) of them, where n is the number of CPU's you have (including hypherthreaded CPU's). A value of 0 forces pluto to do all operations in the main process. A value of -1 tells pluto to perform the above calculation. Any other value forces the number to that amount.
    crlcheckinterval
    • interval, specified in seconds, after which pluto will verify loaded X.509 CRL's for expiration. If any of the CRL's is expired, or if they previously failed to get updated, a new attempt at updating the CRL is made. The first attempt to update a CRL is started at two times the crlcheckinterval. If set to 0, which is also the default value if this option is not specified, CRL updating is disabled.
    strictcrlpolicy
    • if not set, pluto is tolerant about missing or expired X.509 Certificate Revocation Lists (CRL's), and will allow peer certificates as long as they do not appear on an expired CRL. When this option is enabled, all connections with an expired or missing CRL will be denied. Active connections will be terminated at rekey time. This setup is more secure, but also dangerous. If the CRL is fetched through an IPsec tunnel with a CRL that expired, the entire VPN server will be dead in the water until a new CRL is manually transferred to the machine (if it allows non-IPsec connections). Acceptable values are yes or no (the default).
    forwardcontrol
    • This option is obsolete and ignored. Please use net.ipv4.ip_forward = 0 in /etc/sysctl.conf instead to control the ip forwarding behaviour.
    rp_filter
    • This option is obsolete and ignored. Please use the net.ipv4.conf/[iface]/rp_filter = 0 options in /etc/sysctl.conf instead. This option is badly documented; it must be 0 in many cases for ipsec to function.
    syslog
    • the syslog(2) “facility” name and priority to use for startup/shutdown log messages, default daemon.error.
    klipsdebug
    • how much KLIPS debugging output should be logged. An empty value, or the magic value none, means no debugging output (the default). The magic value all means full output. Otherwise only the specified types of output (a quoted list, names separated by white space) are enabled; for details on available debugging types, see ipsec_klipsdebug(8). This KLIPS option has no effect on NETKEY, Windows or BSD stacks.
    plutodebug
    • how much Pluto debugging output should be logged. An empty value, or the magic value none, means no debugging output (the default). The magic value all means full output. Otherwise only the specified types of output (a quoted list, names without the --debug- prefix, separated by white space) are enabled; for details on available debugging types, see ipsec_pluto(8).
    uniqueids
    • whether a particular participant ID should be kept unique, with any new (automatically keyed) connection using an ID from a different IP address deemed to replace all old ones using that ID. Acceptable values are yes (the default) and no. Participant IDs normally are unique, so a new (automatically-keyed) connection using the same ID is almost invariably intended to replace an old one.
    plutorestartoncrash
    • prevent pluto from restarting after it crashed. This option should only be used when debugging a crasher. It will prevent overwriting a core file on a new start, or a cascade of core files. This option is also required if used with plutostderrlog= to avoid clearing the logs of the crasher. Values can be yes (the default) or no.
    plutoopts
    • additional options to pass to pluto upon startup. See ipsec_pluto(8).
    plutostderrlog
    • do not use syslog, but rather log to stderr, and direct stderr to the argument file.
    pluto
    • whether to start Pluto or not; Values are yes (the default) or no (useful only in special circumstances).
    plutowait
    • should Pluto wait for each negotiation attempt that is part of startup to finish before proceeding with the next? Values are yes or no (the default).
    prepluto
    • shell command to run before starting Pluto (e.g., to decrypt an encrypted copy of the ipsec.secrets file). It's run in a very simple way; complexities like I/O redirection are best hidden within a script. Any output is redirected for logging, so running interactive commands is difficult unless they use /dev/tty or equivalent for their interaction. Default is none.
    postpluto
    • shell command to run after starting Pluto (e.g., to remove a decrypted copy of the ipsec.secrets file). It's run in a very simple way; complexities like I/O redirection are best hidden within a script. Any output is redirected for logging, so running interactive commands is difficult unless they use /dev/tty or equivalent for their interaction. Default is none.
    dumpdir
    • in what directory should things started by setup (notably the Pluto daemon) be allowed to dump core? The empty value (the default) means they are not allowed to.
    fragicmp
    • whether a tunnel's need to fragment a packet should be reported back with an ICMP message, in an attempt to make the sender lower his PMTU estimate; acceptable values are yes (the default) and no. This KLIPS option has no effect on NETKEY, Windows or BSD stacks.
    hidetos
    • whether a tunnel packet's TOS field should be set to 0 rather than copied from the user packet inside; acceptable values are yes (the default) and no. This KLIPS option has no effect on NETKEY, Windows or BSD stacks.
    overridemtu
    • value that the MTU of the ipsecn interface(s) should be set to, overriding IPsec's (large) default. This parameter is needed only in special situations. This KLIPS option has no effect on NETKEY, Windows or BSD stacks.

IMPLICIT CONNS

  • The system automatically defines several conns to implement default policy groups. Each can be overridden by explicitly defining a new conn with the same name. If the new conn has auto=ignore, the definition is suppressed. Here are the automatically supplied definitions.
    • conn clear
    plutodebug
    • how much Pluto debugging output should be logged. An empty value, or the magic value none, means no debugging output (the default). The magic value all means full output. Otherwise only the specified types of output (a quoted list, names without the --debug- prefix, separated by white space) are enabled; for details on available debugging types, see ipsec_pluto(8).
    uniqueids
    • whether a particular participant ID should be kept unique, with any new (automatically keyed) connection using an ID from a different IP address deemed to replace all old ones using that ID. Acceptable values are yes (the default) and no. Participant IDs normally are unique, so a new (automatically-keyed) connection using the same ID is almost invariably intended to replace an old one.
    plutorestartoncrash
    • prevent pluto from restarting after it crashed. This option should only be used when debugging a crasher. It will prevent overwriting a core file on a new start, or a cascade of core files. This option is also required if used with plutostderrlog= to avoid clearing the logs of the crasher. Values can be yes (the default) or no.
    plutoopts
    • additional options to pass to pluto upon startup. See ipsec_pluto(8).
    plutostderrlog
    • do not use syslog, but rather log to stderr, and direct stderr to the argument file.
    pluto
    • whether to start Pluto or not; Values are yes (the default) or no (useful only in special circumstances).
    plutowait
    • should Pluto wait for each negotiation attempt that is part of startup to finish before proceeding with the next? Values are yes or no (the default).
    prepluto
    • shell command to run before starting Pluto (e.g., to decrypt an encrypted copy of the ipsec.secrets file). It's run in a very simple way; complexities like I/O redirection are best hidden within a script. Any output is redirected for logging, so running interactive commands is difficult unless they use /dev/tty or equivalent for their interaction. Default is none.
    postpluto
    • shell command to run after starting Pluto (e.g., to remove a decrypted copy of the ipsec.secrets file). It's run in a very simple way; complexities like I/O redirection are best hidden within a script. Any output is redirected for logging, so running interactive commands is difficult unless they use /dev/tty or equivalent for their interaction. Default is none.
    dumpdir
    • in what directory should things started by setup (notably the Pluto daemon) be allowed to dump core? The empty value (the default) means they are not allowed to.
    fragicmp
    • whether a tunnel's need to fragment a packet should be reported back with an ICMP message, in an attempt to make the sender lower his PMTU estimate; acceptable values are yes (the default) and no. This KLIPS option has no effect on NETKEY, Windows or BSD stacks.
    hidetos
    • whether a tunnel packet's TOS field should be set to 0 rather than copied from the user packet inside; acceptable values are yes (the default) and no. This KLIPS option has no effect on NETKEY, Windows or BSD stacks.
    overridemtu
    • value that the MTU of the ipsecn interface(s) should be set to, overriding IPsec's (large) default. This parameter is needed only in special situations. This KLIPS option has no effect on NETKEY, Windows or BSD stacks.

IMPLICIT CONNS

  • The system automatically defines several conns to implement default policy groups. Each can be overridden by explicitly defining a new conn with the same name. If the new conn has auto=ignore, the definition is suppressed. Here are the automatically supplied definitions.
    • conn clear
      • type=passthrough authby=never left=%defaultroute right=%group auto=route
      conn clear-or-private
      • type=passthrough left=%defaultroute leftid=%myid right=%opportunisticgroup failureshunt=passthrough keyingtries=3 ikelifetime=1h salifetime=1h rekey=no auto=route
      conn private-or-clear
      • type=tunnel left=%defaultroute leftid=%myid right=%opportunisticgroup failureshunt=passthrough keyingtries=3 ikelifetime=1h salifetime=1h rekey=no auto=route
      conn private
      • type=tunnel left=%defaultroute leftid=%myid right=%opportunisticgroup failureshunt=drop keyingtries=3 ikelifetime=1h salifetime=1h rekey=no auto=route
      conn block
      • type=reject authby=never left=%defaultroute right=%group auto=route
      # default policy conn packetdefault
      • type=tunnel left=%defaultroute leftid=%myid left=0.0.0.0/0 right=%opportunistic failureshunt=passthrough keyingtries=3 ikelifetime=1h salifetime=1h rekey=no auto=route
    These conns are not affected by anything in conn %default. They will only work if %defaultroute works. The leftid will be the interfaces IP address; this requires that reverse DNS records be set up properly. The implicit conns are defined after all others. It is appropriate and reasonable to use also=private-or-clear (for example) in any other opportunistic conn.

POLICY GROUP FILES

  • The optional files under /etc/ipsec.d/policy, including
    • /etc/ipsec.d/policies/clear /etc/ipsec.d/policies/clear-or-private /etc/ipsec.d/policies/private-or-clear /etc/ipsec.d/policies/private /etc/ipsec.d/policies/block
    may contain policy group configuration information to supplement ipsec.conf. Their contents are not security-sensitive. These files are text files. Each consists of a list of CIDR blocks, one per line. White space followed by # followed by anything to the end of the line is a comment and is ignored, as are empty lines. A connection in ipsec.conf which has right=%group or right=%opportunisticgroup is a policy group connection. When a policy group file of the same name is loaded, with
    • ipsec auto --rereadgroups
    or at system start, the connection is instantiated such that each CIDR block serves as an instance's right value. The system treats the resulting instances as normal connections. For example, given a suitable connection definition private, and the file /etc/ipsec.d/policy/private with an entry 192.0.2.3, the system creates a connection instance private#192.0.2.3. This connection inherits all details from private, except that its right client is 192.0.2.3.

DEFAULT POLICY GROUPS

  • The standard Openswan install includes several policy groups which provide a way of classifying possible peers into IPsec security classes: private (talk encrypted only), private-or-clear (prefer encryption), clear-or-private (respond to requests for encryption), clear and block. Implicit policy groups apply to the local host only, and are implemented by the IMPLICIT CONNECTIONS described above.

CHOOSING A CONNECTION [THIS SECTION IS EXTREMELY OUT OF DATE

  • When choosing a connection to apply to an outbound packet caught with a %trap, the system prefers the one with the most specific eroute that includes the packet's source and destination IP addresses. Source subnets are examined before destination subnets. For initiating, only routed connections are considered. For responding, unrouted but added connections are considered.

    When choosing a connection to use to respond to a negotiation which doesn't match an ordinary conn, an opportunistic connection may be instantiated. Eventually, its instance will be /32 -> /32, but for earlier stages of the negotiation, there will not be enough information about the client subnets to complete the instantiation.

FILES

  • /etc/ipsec.conf /etc/ipsec.d/policies/clear /etc/ipsec.d/policies/clear-or-private /etc/ipsec.d/policies/private-or-clear /etc/ipsec.d/policies/private /etc/ipsec.d/policies/block

SEE ALSO

  • ipsec(8), ipsec_ttoaddr(8), ipsec_auto(8), ipsec_manual(8), ipsec_rsasigkey(8)

HISTORY

BUGS

  • Before reporting new bugs, please ensure you are using the latest version of Openswan, and if not using KLIPS, please ensure you are using the latest kernel code for your IPsec stack. When type or failureshunt is set to drop or reject, Openswan blocks outbound packets using eroutes, but assumes inbound blocking is handled by the firewall. Openswan offers firewall hooks via an “updown” script. However, the default ipsec _updown provides no help in controlling a modern firewall. Including attributes of the keying channel (authentication methods, ikelifetime, etc.) as an attribute of a connection, rather than of a participant pair, is dubious and incurs limitations. The use of %any with the protoport= option is ambiguous. Should the SA permits any port through or should the SA negotiate any single port through? The first is a basic conn with a wildcard. The second is a template. The second is the current behaviour, and it's wrong for quite a number of uses involving TCP. The keyword %one may be introduced in the future to separate these two cases. ipsec_manual is not nearly as generous about the syntax of subnets, addresses, etc. as the usual Openswan user interfaces. Four-component dotted-decimal must be used for all addresses. It is smart enough to translate bit-count netmasks to dotted-decimal form. It would be good to have a line-continuation syntax, especially for the very long lines involved in RSA signature keys. First packet caching is only implemented for the KLIPS(NG) and MAST stacks. NETKEY returns POSIX-breaking responses, visiable as connect: Resource temporarily unavailable errors. This affects Opportunistic Encryption and DPD. Functionality on the BSD and Windows stacks is unknown. Some state information is only available when using KLIPS, and will return errors on other IPsec stacks. These include ipsec eroute, ipsec spi and ipsec look. Multiple L2TP clients behind the same NAT router, and multiple L2TP clients behind different NAT routers using the same Virtual IP is currently only working for the KLIPSNG stack. The ability to specify different identities, authby, and public keys for different automatic-keyed connections between the same participants is misleading; this doesn't work dependably because the identity of the participants is not known early enough. This is especially awkward for the “Road Warrior” case, where the remote IP address is specified as 0.0.0.0, and that is considered to be the “participant” for such connections. In principle it might be necessary to control MTU on an interface-by-interface basis, rather than with the single global override that overridemtu provides. This feature is planned for a future release. A number of features which could be implemented in both manual and automatic keying actually are not yet implemented for manual keying. This is unlikely to be fixed any time soon. If conns are to be added before DNS is available, left=FQDN, leftnextop=FQDN, and leftrsasigkey=%dnsonload will fail. ipsec_pluto(8) does not actually use the public key for our side of a conn but it isn't generally known at a add-time which side is ours (Road Warrior and Opportunistic conns are currently exceptions). The myid option does not affect explicit
    • ipsec auto --add or ipsec auto --replace commands for implicit conns.

[FIXME: source] 04/21/2011 IPSEC.CONF(5)