Differences between revisions 68 and 69
Revision 68 as of 2010-05-03 18:17:01
Size: 17760
Editor: GeoffSimmons
Comment: rndis_wlan: clarify supported F5D7051 revision.
Revision 69 as of 2010-06-27 22:19:42
Size: 17852
Editor: ?JohnBelmonte
Comment: Tivo wireless device
Deletions are marked like this. Additions are marked like this.
Line 290: Line 290:
 * Tivo wireless G (USB-ID 0A5C:BD11) - ''simply a matter of adding alias to the module?''

Translation(s): none

(!) ?Discussion


Broadcom 43xx wireless devices

This page describes how to enable support for WiFi devices based on Broadcom 4301, 4303, 4306, 4309, 4311, 4312, 4318 and 4320 chipsets on Debian systems.

Identification

<!> The PCI-Id isn't sufficient to determine the Broadcom chipset within.

The relevant driver has built-in logic to probe the actual chipset, for example:

  • b43-phy0: Broadcom 4306 WLAN found

Refer to http://www.linuxwireless.org/en/users/Drivers/b43#Known_PCI_devices for more information.

Drivers

There are multiple drivers supporting Broadcom wireless LAN chipsets.

Linux native drivers:

More information on b43/b43legacy can be found on the Linux Wireless b43 driver page. bcm43xx is no longer developed. Note that bcm43xx, b43, b43legacy and wl do not support any USB devices based on Broadcom wireless chipsets.

Using Windows' binary drivers:

  • NDISwrapper plus the relevant Windows NDIS driver. This is a workaround for devices not supported natively by Linux, such as USB devices based on Broadcom wireless chipsets (other than the BCM4320 USB).

b43 and b43legacy

For Linux 2.6.24 and later kernels. Both drivers are included as modules in Debian kernel images.

Using Testing? Skip to the Squeeze section.

Lenny, Etch

  • <!> Etch users: These drivers are not present in the stock 2.6.18 kernel.

  • Install an EtchAndAHalf kernel: apt-cache search linux-image-2.6- | grep etchnhalf and install a package appropriate for your system.

  • Restart your system with this kernel before continuing.

The b43 driver supports modern Broadcom 802.11g wireless chipsets. The b43legacy driver supports Broadcom 802.11b-only devices and BCM4306 revision 2 chipsets.

The b43 driver requires version 4 firmware, whereas the b43legacy driver requires version 3 firmware. Firmware must be downloaded, which can be performed by the b43-fwcutter package during installation. An Internet connection is required.

  1. Add a "contrib" component to /etc/apt/sources.list for your Debian version, for example:

    # Debian Lenny/5.0
    deb http://ftp.us.debian.org/debian lenny main contrib non-free

    or

    # Debian Etch/4.0
    deb http://ftp.us.debian.org/debian etch main contrib non-free
  2. Update the list of available packages and install the b43-fwcutter and wireless-tools packages:

    aptitude update
    aptitude install b43-fwcutter wireless-tools

    If you have an Internet connection available, allow the b43-fwcutter package to fetch and extract firmware.

  3. The necessary kernel module should be automatically loaded. If necessary, it can be manually loaded via either:

    modprobe b43

    or

    modprobe b43legacy
  4. Verify your device has an available interface:

    iwconfig
  5. Raise the interface to activate the radio, for example:

    ifconfig wlan0 up
  6. Configure your wireless interface as appropriate.

Troubleshooting
  • Examine the kernel ring buffer (dmesg(1)) to verify the required firmware files are being loaded by the driver. Lack of firmware is the usual reason for the "SIOCSIFFLAGS: No such file or directory" error message.

Squeeze

The b43 driver supports modern Broadcom 802.11g wireless chipsets. The b43legacy driver supports Broadcom 802.11b-only devices and BCM4306 revision 2 chipsets.

The b43 driver requires version 4 firmware, whereas the b43legacy driver requires version 3 firmware. Firmware must be downloaded, which can be performed by the firmware-b43-installer, firmware-b43legacy-installer or firmware-b43-lpphy-installer packages during installation. An Internet connection is required.

{i} The b43-fwcutter package (as of 1:013~git20100413-1) no longer acquires firmware, separate installer packages are now used.

  1. Add a "contrib" component to /etc/apt/sources.list, for example:

    # Debian Squeeze (testing)
    deb http://ftp.us.debian.org/debian squeeze main contrib non-free
  2. Update the list of available packages and install the wireless-tools package:

    aptitude update
    aptitude install wireless-tools
  3. Install the appropriate firmware installer package:

    For 802.11g devices with a BCM4306 revision 3, BCM4309, BCM4311, BCM4312 (not LP-PHY) or BCM4318 chipset, install firmware-b43-installer:

    aptitude install firmware-b43-installer

    For 802.11g devices with a BCM4312 LP-PHY chipset (PCI-ID 14E4:4315), install firmware-b43-lpphy-installer:

    aptitude install firmware-b43-lpphy-installer

    For 802.11b devices with a BCM4301, BCM4303 or BCM4306 revision 2 chipset, install firmware-b43legacy-installer:

    aptitude install firmware-b43legacy-installer
    A PCI ID check will be performed to prevent incorrect firmware installation. When satisfied, the relevant Broadcom proprietary driver will be acquired, the firmware within will be extracted and installed.
  4. The necessary kernel module should be automatically loaded. If necessary, it can be manually loaded via either:

    modprobe b43

    or

    modprobe b43legacy
  5. Verify your device has an available interface:

    iwconfig
  6. Raise the interface to activate the radio, for example:

    ifconfig wlan0 up
  7. Configure your wireless interface as appropriate.

Troubleshooting
  • Examine the kernel ring buffer (dmesg(1)) to verify the required firmware files are being loaded by the driver. Lack of firmware is the usual reason for the "SIOCSIFFLAGS: No such file or directory" error message.

rndis_wlan

For Linux 2.6.25 and later kernels. This is included as a module in Debian kernel images.

  • <!> Etch users: This driver is not present in the stock 2.6.18 kernel.

  • Install a 2.6.26 kernel from Debian Backports. Once your sources are configured: apt-cache search linux-image-2.6.26 and install a package appropriate for your system.

  • Restart your system with this kernel before continuing.

The rndis_wlan driver supports wireless RNDIS1 chipsets, of which the Broadcom 4320 USB chipset is the only one known at this time. This driver does not require firmware to be installed.

  • {i} Belkin F5D7051 v1000 users: Due to the inclusion of its vendor and device IDs, an Ralink RT2500USB driver will be incorrectly loaded for this device. Please blacklist the rt2500usb module before continuing, see KernelModuleBlacklisting. The F5D7051 v3000 is not supported.

  1. Install the wireless-tools package:

    aptitude update
    aptitude install wireless-tools
  2. Physically connect the device to your system.
  3. The necessary kernel module should be automatically loaded. If necessary, it can be manually loaded via:

    modprobe rndis_wlan
  4. Verify your device has an available interface:

    iwconfig
  5. Raise the interface to activate the radio, for example:

    ifconfig wlan0 up
  6. Configure your wireless interface as appropriate.

Troubleshooting

  • This driver does not support connections to hidden WPA networks at this time.

  • If you are attempting to use a Belkin F5D7051 v1000 device, blacklist the rt2500usb module as advised earlier and execute modprobe -r rt2500usb to unload it.

  • Known problems with this driver are documented on its homepage.

bcm43xx (Etch with 2.6.18 kernel only)

For Linux kernels earlier than 2.6.24. This is included as a module in Debian kernel images.

The bcm43xx driver requires firmware which must be downloaded, which can be performed by the etch-volatile/bcm43xx-fwcutter package during installation.

  1. Add the Debian Volatile repository (including the "contrib" component) to your /etc/apt/sources.list file, for example:

    # Debian Volatile (Etch/4.0)
    deb http://volatile.debian.org/debian-volatile etch/volatile main contrib non-free
  2. Update the list of available packages and install the etch-volatile/bcm43xx-fwcutter and etch/wireless-tools packages:

    aptitude update
    aptitude install bcm43xx-fwcutter wireless-tools

    If you have an Internet connection available, allow the etch-volatile/bcm43xx-fwcutter package to fetch and extract firmware.

  3. The necessary kernel module should be automatically loaded. If necessary, it can be manually loaded via:

    modprobe bcm43xx
  4. Verify your device has an available interface:

    iwconfig
  5. Raise the interface to activate the radio, for example:

    ifconfig eth1 up
  6. Configure your wireless interface as appropriate.

Troubleshooting

  • Examine the kernel ring buffer (dmesg(1)) to verify the required firmware files are being loaded by the driver. Lack of firmware is the usual reason for the "SIOCSIFFLAGS: No such file or directory" error message.

    • Ensure that you have installed the etch-volatile/bcm43xx-fwcutter package from Debian Volatile.

    • Run dpkg-reconfigure -plow bcm43xx-fwcutter to fetch and extract firmware again. Firmware will only be fetched if not already present in the /lib/firmware directory on your system.

  • Your device may be detected (or better supported) with the b43 or b43legacy driver.

NDISwrapper

  • This should only be used as a last resort, if the device is not supported by the native drivers (e.g. Broadcom USB devices, other than the BCM4320 USB).
  • Etch users: Before resorting to NDISwrapper, try using the b43/b43legacy drivers.

Blacklist native drivers

If loaded, the bcm43xx and b43/b43legacy drivers will conflict with NDISwrapper. To unload and disable:

Lenny, Etch with 2.6.24 kernel

modprobe -r b43 b43legacy
echo -e blacklist b43\\nblacklist b43legacy >> /etc/modprobe.d/local.conf

Etch with 2.6.18 kernel

modprobe -r bcm43xx
echo blacklist bcm43xx >> /etc/modprobe.d/local.conf

Installation

Kernel module and NDIS driver installation is described on the NDISwrapper page.

Supported Devices

b43

The page HowToIdentifyADevice/PCI explains how to identify a PCI device.

Unsupported

  • BCM4313 (PCI-ID 14E4:4727)
  • BCM4321 (PCI-IDs 14E4:4328, 14E4:4329)
  • BCM4322 (PCI-ID 14E4:432B)

Support for the above chipsets is available via the non-free vendor driver, see wl.

b43legacy

The page HowToIdentifyADevice/PCI explains how to identify a PCI device.

rndis_wlan

The page HowToIdentifyADevice/USB explains how to identify a USB device.

The following list is based on the alias fields of modinfo rndis_wlan on Lenny.

  • USB: 0411:004B MelCo., Inc. (Device name unknown)
    USB: 0411:00BC MelCo., Inc. (Device name unknown)
    USB: 050D:011B Belkin Components (Device name unknown)
    USB: 0A5C:D11B Broadcom Corp. (Device name unknown)
    USB: 0B05:1717 ASUSTek Computer, Inc. (Device name unknown)
    USB: 0BAF:0111 U.S. Robotics (Device name unknown)
    USB: 0BAF:011B U.S. Robotics Wireless MAXg Adapter
    USB: 13B1:000E Linksys WUSB54GS v1 802.11g Adapter [Broadcom 4320 USB]
    USB: 13B1:0014 Linksys WUSB54GS v2 802.11g Adapter [Broadcom 4320 USB]
    USB: 13B1:0026 Linksys WUSB54GSC v1 802.11g Adapter [Broadcom 4320 USB]
    USB: 1690:0715 Askey Computer Corp. [hex] Voyager 1055 Laptop Adapter
    USB: 1799:011B (Vendor name unknown) (Device name unknown)

    http://wireless.kernel.org/en/users/Drivers/rndis_wlan#supported_chips - supported chipsets

Unsupported

  • Belkin F5D7051 v3000 (USB-ID 4317:0711)

  • Tivo wireless G (USB-ID 0A5C:BD11) - simply a matter of adding alias to the module?

Refer to the NDISwrapper page for device support.

bcm43xx

The page HowToIdentifyADevice/PCI explains how to identify a PCI device.

The following list is based on the alias fields of modinfo bcm43xx on Etch.

  • PCI: 14E4:4301 Broadcom Corporation BCM4303 802.11b Wireless LAN Controller
    PCI: 14E4:4307 Broadcom Corporation BCM4307 802.11b Wireless LAN Controller
    PCI: 14E4:4318 Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller
    PCI: 14E4:4319 Broadcom Corporation BCM4311 [AirForce 54g] 802.11a/b/g PCI Express Transceiver
    PCI: 14E4:4320 Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller
    PCI: 14E4:4324 Broadcom Corporation BCM4309 802.11a/b/g
    PCI: 14E4:4325 Broadcom Corporation BCM43xG 802.11b/g

{i} Although listed above, the BCM4311 is only supported by this driver from kernel 2.6.20.6. Use of the b43 driver is recommended.

See Also


CategoryHardware | CategoryWireless

  1. Microsoft's unofficial CDC ACM variant, see USB CDC on Wikipedia. (1)