11383
Comment: spelling
|
11387
section -> component
|
Deletions are marked like this. | Additions are marked like this. |
Line 48: | Line 48: |
1. Add the Debian Volatile repository (including the "contrib" section) to your {{{/etc/apt/sources.list}}} file, for example: | 1. Add the Debian Volatile repository (including the "contrib" component) to your {{{/etc/apt/sources.list}}} file, for example: |
Line 92: | Line 92: |
1. Add a "contrib" section to {{{/etc/apt/sources.list}}} for your Debian version, for example: | 1. Add a "contrib" component to {{{/etc/apt/sources.list}}} for your Debian version, for example: |
Broadcom 43xx wireless devices
This page describes how to enable support for WiFi devices based on Broadcom 4303, 4306, 4309, 4311, 4312 and 4318 wireless chipsets.
?TableOfContents(3)
Device Identification
The page ["HowToIdentifyADevice/PCI"] explains how to identify a PCI device. For example:
update-pciids lspci -nn
Your Broadcom PCI wireless device should be listed:
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN [14E4:4311] (rev 01)
The [:HowToIdentifyADevice/PCI#pci-id:PCI-Id] isn't sufficient to determine the Broadcom chipset within. The relevant driver has built-in logic to probe the actual chipset.
Drivers
There are multiple drivers supporting Broadcom wireless LAN chipsets.
Linux native drivers:
[#bcm43xx bcm43xx] driver ([http://bcm43xx.berlios.de/?go=devices supported devices])
- included in mainline kernels from 2.6.17-rc2
- disabled in Debian 2.6.24 and later kernels
- driver was removed from the mainline kernel in 2.6.26
[#b43 b43] driver ([http://wireless.kernel.org/en/users/Drivers/b43#supported supported devices])
- the new driver for modern 802.11g and 802.11a chipsets
- introduced in kernel 2.6.24
[#b43 b43legacy] driver ([http://wireless.kernel.org/en/users/Drivers/b43#supported supported devices])
- for legacy 802.11b-only devices and the BCM4306 revision 2 chipset
- introduced in kernel 2.6.24
The bcm43xx driver is no longer developed. More information on the b43/b43legacy drivers can be found on the Linux Wireless [http://wireless.kernel.org/en/users/Drivers/b43#b43andb43legacy b43 driver page]. Note that none of the above drivers support USB devices based on Broadcom wireless chipsets.
Using Windows' binary drivers:
- [#ndiswrapper NDISwrapper] plus the relevant Windows NDIS driver. This is a workaround for devices not supported natively by Linux, such as USB devices based on Broadcom wireless chipsets.
?Anchor(bcm43xx)
bcm43xx (Etch with 2.6.18 kernel only)
Using [:Lenny:]? Skip to the [#b43 b43/b43legacy] section.
For kernels earlier than 2.6.24. This is included as a module in Debian kernel images. The bcm43xx driver requires firmware which must be downloaded separately (can be performed by the etch-volatile/bcm43xx-fwcutter package during installation).
You are required to install the etch-volatile/bcm43xx-fwcutter package from the [:DebianVolatile:Debian Volatile] repository due to bug 437488. Installing the etch/bcm43xx-fwcutter package will fail to download firmware if requested.
1. Add the Debian Volatile repository (including the "contrib" component) to your /etc/apt/sources.list file, for example:
# Debian Volatile (Etch/4.0) deb http://volatile.debian.org/debian-volatile etch/volatile main contrib non-free
2. Update the list of available packages and install the etch-volatile/bcm43xx-fwcutter and etch/wireless-tools packages:
aptitude update aptitude install bcm43xx-fwcutter wireless-tools
If you have an Internet connection available, allow the etch-volatile/bcm43xx-fwcutter package to fetch and extract firmware.
3. The necessary kernel module should be [:Modules:automatically loaded]. If necessary, it can be manually loaded via:
modprobe bcm43xx
4. Verify your device has an available interface:
iwconfig
5. Raise the interface to activate the radio, for example:
ifconfig eth1 up
6. [:WiFi/HowToUse:Configure] your wireless interface as appropriate.
?Anchor(bcm43xx_troubleshoot)
Troubleshooting
- Examine the kernel ring buffer (dmesg) to verify the required firmware files are being loaded by the driver. Lack of firmware is the usual reason for the "SIOCSIFFLAGS: No such file or directory" error message.
Ensure that you have installed the etch-volatile/bcm43xx-fwcutter package from [:DebianVolatile:Debian Volatile].
Run dpkg-reconfigure -plow bcm43xx-fwcutter to fetch and extract firmware again. Firmware will only be fetched if not already present in the /lib/firmware directory on your system.
Your device may be detected (or better supported) through the b43 or b43legacy drivers. Install an [:EtchAndAHalf:] kernel image (apt-cache search linux-image-2.6.24-etchnhalf and install a package appropriate for your system), restart your system to boot using this kernel, then follow the [#b43 b43/b43legacy] driver procedure below.
?Anchor(b43)
b43 and b43legacy
For 2.6.24 and later kernels. Both drivers are included as modules in Debian kernel images.
Etch users: These drivers are not present in the stock 2.6.18 kernel. Install and boot an [:EtchAndAHalf:] kernel (apt-cache search linux-image-2.6.24-etchnhalf and install a package appropriate for your system) before continuing.
The b43 driver supports modern Broadcom 802.11g wireless chipsets. The b43legacy driver supports Broadcom 802.11b-only devices and BCM4306 revision 2 chipsets.
The b43 driver requires version 4 firmware, whereas the b43legacy driver requires version 3 firmware. All firmware must be downloaded separately, which can be performed by the b43-fwcutter package during installation.
1. Add a "contrib" component to /etc/apt/sources.list for your Debian version, for example:
# Debian Etch/4.0 deb http://ftp.us.debian.org/debian etch main contrib non-free
# Debian Lenny deb http://ftp.us.debian.org/debian lenny main contrib non-free
2. Install the b43-fwcutter and wireless-tools packages:
aptitude update aptitude install b43-fwcutter wireless-tools
If you have an Internet connection available, allow the b43-fwcutter package to fetch and extract firmware.
3. The necessary kernel module should be [:Modules:automatically loaded]. If necessary, it can be manually loaded via either:
modprobe b43
modprobe b43legacy
4. Verify your device has an available interface:
iwconfig
5. Raise the interface to activate the radio, for example:
ifconfig wlan0 up
6. [:WiFi/HowToUse:Configure] your wireless interface as appropriate.
Troubleshooting
- Examine the kernel ring buffer (dmesg) to verify the required firmware files are being loaded by the driver. Lack of firmware is the usual reason for the "SIOCSIFFLAGS: No such file or directory" error message.
Run dpkg-reconfigure -plow b43-fwcutter to fetch and extract firmware again. Firmware will only be fetched if not already present in the /lib/firmware/[b43|b43legacy] directories on your system.
If necessary, firmware can be manually acquired and extracted using the b43-fwcutter utility, see http://wireless.kernel.org/en/users/Drivers/b43#firmwareinstallation
?Anchor(b43_legacy)
?Anchor(ndiswrapper)
NDISwrapper
- This should only be used as a last resort, if the device is not supported by the native drivers (eg. Broadcom USB devices).
- Etch users: Before resorting to NDISwrapper, try using the b43/b43legacy drivers via an [:EtchAndAHalf:] kernel, as described in the [#bcm43xx_troubleshoot bcm43xx troubleshooting] section.
[:NdisWrapper:More information] on NDISwrapper is available on this wiki.
Blacklist native driver
If loaded, the native bcm43xx driver will conflict with NDISwrapper. To unload and disable:
modprobe -r bcm43xx echo blacklist bcm43xx >> /etc/modprobe.d/blacklist.local
Module installation (via module-assistant)
aptitude install module-assistant wireless-tools && m-a prepare && m-a a-i ndiswrapper modprobe ndiswrapper echo ndiswrapper >> /etc/modules
NDISwrapper is now installed on your system. Install the required [#ndisdriver NDIS driver] as necessary.
Module Installation (manual)
The following procedure is only necessary for Etch systems which require a version of NDISwrapper greater than 1.28.
Install necessary development packages, along with wireless-tools:
aptitude install build-essential linux-headers-$(uname -r) wireless-tools
Download and compile the NDISwrapper [http://sourceforge.net/project/showfiles.php?group_id=93482 source code]. For example, to acquire and build NDISwrapper version 1.53:
mkdir tmp && cd tmp wget http://superb-east.dl.sourceforge.net/sourceforge/ndiswrapper/ndiswrapper-1.53.tar.gz tar xvf ndiswrapper-1.53.tar.gz cd ndiswrapper-1.53 make su make install modprobe ndiswrapper echo ndiswrapper >> /etc/modules
NDISwrapper is now installed on your system. Install the required [#ndisdriver NDIS driver] as necessary.
?Anchor(ndisdriver)
Install NDIS driver
The following procedure is specific to the "Dell Wireless Card 1390" (man: 14e4, dev: 4311) device and is provided as an example only. Consult the [:NdisWrapper:NDISwrapper page] for links to further information on your specific device.
1. Install the unzip package:
aptitude install unzip
2. Acquire an archive containing the NDIS driver from Dell's FTP site:
wget http://ftp.us.dell.com/network/R151517.EXE
3. Extract its contents:
unzip -a R151517.EXE
4. Install the NDIS driver:
ndiswrapper -i DRIVER/bcmwl5.inf
5. To verify NDIS driver installation, list the currently installed drivers:
ndiswrapper -l
You should receive the following output:
bcmwl5 : driver installed device (14E4:4311) present
Examine the device
Verify that your device now has an available interface:
iwconfig
You should receive output similar to:
wlan0 IEEE 802.11g ESSID:off/any Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0
You are now able to [:WiFi/HowToUse:configure] your wireless interface as appropriate.
Troubleshooting
- Ensure the bcm43xx driver is unloaded and blacklisted as described earlier.
Read the [:NdisWrapper:NDISwrapper page] on this wiki.
?Anchor(use)
Connecting to the network
See [:WiFi/HowToUse:How To use Wifi network adapter].
See Also
[http://www.linuxwireless.org/en/users/Drivers/b43] - b43, b43legacy homepage;
[http://www.linuxwireless.org/en/users/Drivers/b43#devicefirmware b43 and b43legacy] - device firmware
[http://bcm43xx.berlios.de/?go=devices] - bcm43xx homepage
[http://manpages.debian.net/man/ndiswrapper NDISwrapper] manpages
[http://www.learnaboutlinux.net/wireless_1390.htm Generic bcm43xx and NDISwrapper (Explains it all) ]
[http://ubuntuforums.org/showthread.php?t=297092 NDISwrapper for 1390 only]