Differences between revisions 1 and 14 (spanning 13 versions)
Revision 1 as of 2005-04-21 13:46:11
Size: 506
Editor: anonymous
Comment:
Revision 14 as of 2009-03-16 03:30:00
Size: 2032
Editor: anonymous
Comment: converted to 1.6 markup
Deletions are marked like this. Additions are marked like this.
Line 3: Line 3:
Back to [[[PortsSparc]]] [[[SparcKernelStatus]]]
Line 5: Line 7:
[*] Very detailed netboot [http://lists.debian.org/debian-boot/2005/04/msg00651.html installation notes] for SunBlade 150 using ["RC3"] version of the [http://www.debian.org/devel/debian-installer Debian installer]. Contains the instruction on setting up the rarpd and tftp server for netbooting. Thanks to Wiktor Wandachowicz.  * The official information for the Sarge release is in the [[http://www.debian.org/releases/stable/sparc/|installation guide]] and the [[http://www.debian.org/releases/stable/sparc/release-notes/|release notes]]

 * Very detailed netboot [[http://lists.debian.org/debian-boot/2005/04/msg00651.html|installation notes]] for SunBlade 150 using [[RC3]] version of the [[http://www.debian.org/devel/debian-installer|Debian installer]]. Contains the instructions on setting up the rarpd and tftp server for netbooting. Thanks to Wiktor Wandachowicz. There is also [[http://nishants.net/articles/sunblade150.htm|this howto]] available written by Nishant Sharma.

 * An unofficial [[http://www.acm.cs.rpi.edu/~dilinger/iso.img|netinst iso]] with a all-modular IDE drivers. Fixes the problems with IDE device detection on SunBlades. Unfortunately, this change did not make it to Sarge installer. Thanks to Andres Salomon.
 
 * If you get tired of the partitioner going mad with the currently installed (SunOS) disk on an old slow sparcstation, choose "go back" and then run down to the start a shell option. Then run parted which (a) works and (b) is fast. mklabel sun, mkpart primary ext2 0 x, mkpart primary ext2 x y etc. It seems you have to choose primary and ext2 here ... it doesn't actually do anything. Then quit, and exit the shell too. Go back to the installer's partition manager. Suddenly it is not going bonkers trying to make 67 Mb partitions. Persuade it that the first partition is / and the second is swap ... this will take about 3 minutes each on a sparcstation; no I do not know why the code is so slow. Then become confused because there is no Next button on your serial console. Keep pressing down, past the disk and its partitions and you get the Finish option you wanted.

Installation Notes for Sparc

Back to ?[PortsSparc] ?[SparcKernelStatus]

This page contains links to useful information about installation on various Sparc machines.

  • The official information for the Sarge release is in the installation guide and the release notes

  • Very detailed netboot installation notes for ?SunBlade 150 using ?RC3 version of the Debian installer. Contains the instructions on setting up the rarpd and tftp server for netbooting. Thanks to Wiktor Wandachowicz. There is also this howto available written by Nishant Sharma.

  • An unofficial netinst iso with a all-modular IDE drivers. Fixes the problems with IDE device detection on ?SunBlades. Unfortunately, this change did not make it to Sarge installer. Thanks to Andres Salomon.

  • If you get tired of the partitioner going mad with the currently installed (SunOS) disk on an old slow sparcstation, choose "go back" and then run down to the start a shell option. Then run parted which (a) works and (b) is fast. mklabel sun, mkpart primary ext2 0 x, mkpart primary ext2 x y etc. It seems you have to choose primary and ext2 here ... it doesn't actually do anything. Then quit, and exit the shell too. Go back to the installer's partition manager. Suddenly it is not going bonkers trying to make 67 Mb partitions. Persuade it that the first partition is / and the second is swap ... this will take about 3 minutes each on a sparcstation; no I do not know why the code is so slow. Then become confused because there is no Next button on your serial console. Keep pressing down, past the disk and its partitions and you get the Finish option you wanted.