Content
Novascale R460 "SAS" - Hardware
This is a short list of the Hardware configuration of a Bull Novascale R460 wich tested with Debian GNU/Linux 4.0 (etch). ( a status-list of the tested novascale´s)
CPU: |
2x Intel® Xeon™ Dual Core 1,6GHz, 4MB L2 Cache, 1066 FSB |
HDD: |
4x 73GB SAS 3.5", 15Krpm |
RAM: |
1GB FBD DDR2-667 ECC |
RAID: |
LSI Megaraid SAS5408E 8-CH |
Soundkarte: |
N/A |
Grafikkarte: |
Matrox Graphics, Inc. MGA G200e |
Ethernet: |
Intel® 82563EB Gigabit Ethernet |
Mainbord: |
Intel® ?ServerBoard S5000VSA |
lspci
R460:/# lspci 00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1) 00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) 00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) 00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) 00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 (rev b1) 00:06.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 6 (rev b1) 00:07.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 (rev b1) 00:10.0 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting Registers (rev b1) 00:10.1 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting Registers (rev b1) 00:10.2 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting Registers (rev b1) 00:11.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1) 00:13.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev b1) 00:15.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1) 00:16.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev b1) 00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 09) 00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 09) 00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 09) 00:1d.2 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 (rev 09) 00:1d.3 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 (rev 09) 00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 09) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d9) 00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 09) 00:1f.1 IDE interface: Intel Corporation 631xESB/632xESB IDE Controller (rev 09) 00:1f.3 SMBus: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller (rev 09) 01:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port (rev 01) 01:00.3 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge (rev 01) 02:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 (rev 01) 02:02.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E3 (rev 01) 03:00.0 PCI bridge: Intel Corporation 80333 Segment-A PCI Express-to-PCI Express Bridge 03:00.2 PCI bridge: Intel Corporation 80333 Segment-B PCI Express-to-PCI Express Bridge 04:0e.0 RAID bus controller: LSI Logic / Symbios Logic Unknown device 0411 0c:00.0 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) 0c:00.1 Ethernet controller: Intel Corporation 631xESB/632xESB DPT LAN Controller Copper (rev 01) 0d:05.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068 PCI-X Fusion-MPT SAS (rev 01) 24:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02)
dmesg
Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12etch2) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Wed May 9 23:03:12 UTC 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000099000 (usable) BIOS-e820: 0000000000099000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fee0000 (usable) BIOS-e820: 000000003fee0000 - 000000003fef3000 (ACPI data) BIOS-e820: 000000003fef3000 - 000000003ff80000 (ACPI NVS) BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) 126MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f77b0 On node 0 totalpages: 261856 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 32480 pages, LIFO batch:7 DMI present. ACPI: RSDP (v000 PTLTD ) @ 0x000f7780 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3feee07f ACPI: FADT (v002 INTEL TUMWATER 0x06040000 PTL 0x00000003) @ 0x3fef2e7e ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3fef2f02 ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x3fef2f9c ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x3fef2fd8 ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20050228) @ 0x3feee0b7 ACPI: DSDT (v001 Intel BLAKFORD 0x06040000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled) Processor #6 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled) Processor #7 6:15 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24]) IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. ACPI: IRQ11 used by override. Enabling APIC mode: Flat. Using 2 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Detected 1596.038 MHz processor. Built 1 zonelists. Total pages: 261856 Kernel command line: root=/dev/sda1 ro mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) mapped IOAPIC to ffffb000 (fec80000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1030540k/1047424k available (1544k kernel code, 16176k reserved, 577k data, 196k init, 129920k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3194.65 BogoMIPS (lpj=6389311) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfebfbff 20000000 00000000 00000940 0004e33d 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20060707 CPU0: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3192.10 BogoMIPS (lpj=6384206) CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfebfbff 20000000 00000000 00000940 0004e33d 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 SMP alternatives: switching to SMP code Booting processor 2/6 eip 3000 Initializing CPU#2 Calibrating delay using timer specific routine.. 3192.14 BogoMIPS (lpj=6384292) CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 3 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfebfbff 20000000 00000000 00000940 0004e33d 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#2. CPU2: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 SMP alternatives: switching to SMP code Booting processor 3/7 eip 3000 Initializing CPU#3 Calibrating delay using timer specific routine.. 3192.14 BogoMIPS (lpj=6384287) CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0004e33d 00000000 00000001 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 3 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfebfbff 20000000 00000000 00000940 0004e33d 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#3. CPU3: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06 Total of 4 processors activated (12771.04 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 4 CPUs: passed. Brought up 4 CPUs migration_cost=46,10991 checking if image is initramfs... it is Freeing initrd memory: 4407k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Boot video device is 0000:24:00.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMD0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMD0.BPD0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMD0.BPD2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMF3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *7 10 12) ACPI: PCI Interrupt Link [LNKB] (IRQs *5 7 10 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 5 7 *10 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 *10 12) ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 10 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 5 7 10 12) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs *5 7 10 12) ACPI: PCI Interrupt Link [LNKH] (IRQs 5 7 *10 12) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 9 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Failed to allocate mem resource #9:200000@de200000 for 0000:01:00.3 PCI: Failed to allocate mem resource #9:100000@de100000 for 0000:02:02.0 PCI: Bridge: 0000:03:00.0 IO window: disabled. MEM window: de200000-de2fffff PREFETCH window: de000000-de0fffff PCI: Bridge: 0000:03:00.2 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:02:00.0 IO window: disabled. MEM window: de200000-de2fffff PREFETCH window: de000000-de0fffff PCI: Bridge: 0000:02:02.0 IO window: 2000-2fff MEM window: de300000-de3fffff PREFETCH window: disabled. PCI: Bridge: 0000:01:00.0 IO window: 2000-2fff MEM window: de200000-de3fffff PREFETCH window: de000000-de0fffff PCI: Bridge: 0000:01:00.3 IO window: 3000-3fff MEM window: de400000-de6fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:02.0 IO window: 2000-3fff MEM window: de100000-de6fffff PREFETCH window: de000000-de0fffff PCI: Bridge: 0000:00:03.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:04.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:05.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:07.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: de700000-deffffff PREFETCH window: dd000000-ddffffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:02.0 to 64 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:01:00.0 to 64 ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:02:00.0 to 64 PCI: Setting latency timer of device 0000:03:00.0 to 64 PCI: Setting latency timer of device 0000:03:00.2 to 64 ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:02:02.0 to 64 PCI: Setting latency timer of device 0000:01:00.3 to 64 ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:03.0 to 64 ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:04.0 to 64 ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:05.0 to 64 ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:07.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1c.0 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x40 set to 0x1 audit: initializing netlink socket (disabled) audit(1184070367.124:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] Allocate Port Service[0000:00:02.0:pcie01] PCI: Setting latency timer of device 0000:00:03.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:03.0:pcie00] Allocate Port Service[0000:00:03.0:pcie01] PCI: Setting latency timer of device 0000:00:04.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] Allocate Port Service[0000:00:04.0:pcie01] PCI: Setting latency timer of device 0000:00:05.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:05.0:pcie00] Allocate Port Service[0000:00:05.0:pcie01] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie01] PCI: Setting latency timer of device 0000:00:07.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:07.0:pcie00] Allocate Port Service[0000:00:07.0:pcie01] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:01:00.0 to 64 Allocate Port Service[0000:01:00.0:pcie10] Allocate Port Service[0000:01:00.0:pcie11] PCI: Setting latency timer of device 0000:02:00.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:02:00.0:pcie20] Allocate Port Service[0000:02:00.0:pcie21] PCI: Setting latency timer of device 0000:02:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:02:02.0:pcie20] Allocate Port Service[0000:02:02.0:pcie21] isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: No PS/2 controller found. Probing ports directly. i8042.c: Warning: Keylock active. Failed to disable AUX port, but continuing anyway... Is this a SiS? If AUX port is really absent please use the 'i8042.noaux' option. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Starting balanced_irq Using IPI No-Shortcut mode ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 196k freed Time: tsc clocksource has been installed. ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Processor [CPU2] (supports 8 throttling states) ACPI: Processor [CPU3] (supports 8 throttling states) ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x4 ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x5 ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x6 ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x7 Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI Copyright (c) 1999-2006 Intel Corporation. ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 18 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:0c:00.0 to 64 usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[C] -> GSI 22 (level, low) -> IRQ 82 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 82, io base 0x00001800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx e1000: 0000:0c:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:19:db:6e:51:b6 SCSI subsystem initialized Fusion MPT base driver 3.04.01 Copyright (c) 1999-2005 LSI Logic Corporation megasas: 00.00.03.01 Sun May 14 22:49:52 PDT 2006 Fusion MPT SAS Host driver 3.04.01 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt 0000:0c:00.1[B] -> GSI 19 (level, low) -> IRQ 90 PCI: Setting latency timer of device 0000:0c:00.1 to 64 e1000: 0000:0c:00.1: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:19:db:6e:51:b7 ACPI: PCI Interrupt 0000:00:1d.1[C] -> GSI 22 (level, low) -> IRQ 82 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 82, io base 0x00001820 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 82 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 82, io base 0x00001840 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[C] -> GSI 22 (level, low) -> IRQ 82 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 82, io base 0x00001860 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.7[B] -> GSI 23 (level, low) -> IRQ 98 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 98, io mem 0xdf200000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected ESB2: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[B] -> GSI 19 (level, low) -> IRQ 90 ESB2: chipset revision 9 ESB2: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... usb 4-2: new full speed USB device using uhci_hcd and address 2 hda: MATSHITADVD-ROM SR-8178, ATAPI CD/DVD-ROM drive usb 4-2: configuration #1 chosen from 1 choice usbcore: registered new driver hiddev input: ServerEngines SE USB Device as /class/input/input0 input: USB HID v1.11 Keyboard [ServerEngines SE USB Device] on usb-0000:00:1d.3-2 input: ServerEngines SE USB Device as /class/input/input1 input: USB HID v1.11 Mouse [ServerEngines SE USB Device] on usb-0000:00:1d.3-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ACPI: PCI Interrupt 0000:0d:05.0[A] -> GSI 28 (level, low) -> IRQ 106 mptbase: Initiating ioc0 bringup hda: ATAPI 24X DVD-ROM drive, 256kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ioc0: SAS1068: Capabilities={Initiator} scsi0 : ioc0: LSISAS1068, FwRev=00070e00h, Ports=1, MaxQ=511, IRQ=106 megasas: 0x1000:0x0411:0x1000:0x1001: bus 4:slot 14:func 0 ACPI: PCI Interrupt 0000:04:0e.0[A] -> GSI 18 (level, low) -> IRQ 177 scsi1 : LSI Logic SAS based MegaRAID driver Vendor: HITACHI Model: HUS151473VLS300 Rev: A42A Type: Direct-Access ANSI SCSI revision: 05 Vendor: HITACHI Model: HUS151473VLS300 Rev: A42A Type: Direct-Access ANSI SCSI revision: 05 Vendor: HITACHI Model: HUS151473VLS300 Rev: A42A Type: Direct-Access ANSI SCSI revision: 05 Vendor: HITACHI Model: HUS151473VLS300 Rev: A42A Type: Direct-Access ANSI SCSI revision: 05 Vendor: LSI Model: MegaRAID 8408E Rev: 1.02 Type: Direct-Access ANSI SCSI revision: 05 Vendor: LSI Model: MegaRAID 8408E Rev: 1.02 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 142278656 512-byte hdwr sectors (72847 MB) sda: test WP failed, assume Write Enabled sda: asking for cache data failed sda: assuming drive cache: write through SCSI device sda: 142278656 512-byte hdwr sectors (72847 MB) sda: test WP failed, assume Write Enabled sda: asking for cache data failed sda: assuming drive cache: write through sda: sda1 sda2 < sda5 sda6 > sd 1:2:0:0: Attached scsi disk sda SCSI device sdb: 284557312 512-byte hdwr sectors (145693 MB) sdb: test WP failed, assume Write Enabled sdb: asking for cache data failed sdb: assuming drive cache: write through SCSI device sdb: 284557312 512-byte hdwr sectors (145693 MB) sdb: test WP failed, assume Write Enabled sdb: asking for cache data failed sdb: assuming drive cache: write through sdb: unknown partition table sd 1:2:1:0: Attached scsi disk sdb Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ts: Compaq touchscreen protocol output intel_rng: FWH not detected ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 90 input: PC Speaker as /class/input/input2 Real Time Clock Driver v1.12ac input: PS/2 Generic Mouse as /class/input/input3 Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1 across:2650684k EXT3 FS on sda1, internal journal loop: loaded (max 8 devices) device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ADDRCONF(NETDEV_UP): eth1: link is not ready eth0: no IPv6 routers present SCSI device sdb: 284557312 512-byte hdwr sectors (145693 MB) sdb: test WP failed, assume Write Enabled sdb: asking for cache data failed sdb: assuming drive cache: write through sdb: sdb1 < sdb5 > kjournald starting. Commit interval 5 seconds EXT3 FS on sdb5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb5, internal journal EXT3-fs: mounted filesystem with ordered data mode. usb 2-1: new full speed USB device using uhci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice hub 2-1:1.0: USB hub found hub 2-1:1.0: 3 ports detected usb 2-1.1: new full speed USB device using uhci_hcd and address 3 usb 2-1.1: configuration #1 chosen from 1 choice input: ALCOR macally Kbd Hub as /class/input/input4 input: USB HID v1.00 Keyboard [ALCOR macally Kbd Hub] on usb-0000:00:1d.1-1.1 usb 2-1: USB disconnect, address 2 usb 2-1.1: USB disconnect, address 3
demidecode
# dmidecode 2.8 SMBIOS 2.4 present. 83 structures occupying 3234 bytes. Table at 0x000F0A60. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: Phoenix Technologies LTD Version: 1.0.5S47 Release Date: 02/16/2007 Address: 0xE0270 Runtime Size: 130448 bytes ROM Size: 1024 kB Characteristics: PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported EDD is supported Japanese floppy for NEC 9800 1.2 MB is supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) ACPI is supported USB legacy is supported BIOS boot specification is supported Function key-initiated network boot is supported Targeted content distribution is supported Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: NEC Product Name: NovaScale R460 [N8100-1247E] Version: FR1.0 Serial Number: 8002023300 UUID: 0EA47B00-D598-11DB-8001-0019DB6E510A Wake-up Type: Unknown SKU Number: Not Specified Family: Not Specified Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: MICRO-STAR Product Name: MS-9172-01S Version: 021 Serial Number: 7210831680 Handle 0x0003, DMI type 3, 17 bytes Chassis Information Manufacturer: Type: Rack Mount Chassis Lock: Present Version: 856-060760-004 Serial Number: 01 Asset Tag: 243-413861-961 Boot-up State: Unknown Power Supply State: Unknown Thermal State: Unknown Security Status: Unknown OEM Information: 0x00000000 Handle 0x0004, DMI type 4, 35 bytes Processor Information Socket Designation: CPU#1 Type: Central Processor Family: Xeon Manufacturer: Intel Corporation ID: F6 06 00 00 FF FB EB BF Signature: Type 0, Family 6, Model 15, Stepping 6 Flags: FPU (Floating-point unit on-chip) VME (Virtual mode extension) DE (Debugging extension) PSE (Page size extension) TSC (Time stamp counter) MSR (Model specific registers) PAE (Physical address extension) MCE (Machine check exception) CX8 (CMPXCHG8 instruction supported) APIC (On-chip APIC hardware supported) SEP (Fast system call) MTRR (Memory type range registers) PGE (Page global enable) MCA (Machine check architecture) CMOV (Conditional move instruction supported) PAT (Page attribute table) PSE-36 (36-bit page size extension) CLFSH (CLFLUSH instruction supported) DS (Debug store) ACPI (ACPI supported) MMX (MMX technology supported) FXSR (Fast floating-point save and restore) SSE (Streaming SIMD extensions) SSE2 (Streaming SIMD extensions 2) SS (Self-snoop) HTT (Hyper-threading technology) TM (Thermal monitor supported) PBE (Pending break enabled) Version: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz Voltage: 1.3 V External Clock: 333 MHz Max Speed: 3000 MHz Current Speed: 1600 MHz Status: Populated, Enabled Upgrade: Other L1 Cache Handle: 0x0006 L2 Cache Handle: 0x0007 L3 Cache Handle: Not Provided Serial Number: Asset Tag: Part Number: Handle 0x0005, DMI type 4, 35 bytes Processor Information Socket Designation: CPU#2 Type: Central Processor Family: Xeon Manufacturer: Intel Corporation ID: F6 06 00 00 FF FB EB BF Signature: Type 0, Family 6, Model 15, Stepping 6 Flags: FPU (Floating-point unit on-chip) VME (Virtual mode extension) DE (Debugging extension) PSE (Page size extension) TSC (Time stamp counter) MSR (Model specific registers) PAE (Physical address extension) MCE (Machine check exception) CX8 (CMPXCHG8 instruction supported) APIC (On-chip APIC hardware supported) SEP (Fast system call) MTRR (Memory type range registers) PGE (Page global enable) MCA (Machine check architecture) CMOV (Conditional move instruction supported) PAT (Page attribute table) PSE-36 (36-bit page size extension) CLFSH (CLFLUSH instruction supported) DS (Debug store) ACPI (ACPI supported) MMX (MMX technology supported) FXSR (Fast floating-point save and restore) SSE (Streaming SIMD extensions) SSE2 (Streaming SIMD extensions 2) SS (Self-snoop) HTT (Hyper-threading technology) TM (Thermal monitor supported) PBE (Pending break enabled) Version: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz Voltage: 1.3 V External Clock: 333 MHz Max Speed: 3000 MHz Current Speed: 1600 MHz Status: Populated, Enabled Upgrade: Other L1 Cache Handle: 0x0008 L2 Cache Handle: 0x0009 L3 Cache Handle: Not Provided Serial Number: Asset Tag: Part Number: Handle 0x0006, DMI type 7, 19 bytes Cache Information Socket Designation: L1 Cache for CPU#1 Configuration: Enabled, Not Socketed, Level 1 Operational Mode: Write Back Location: Internal Installed Size: 64 KB Maximum Size: 64 KB Supported SRAM Types: Burst Pipeline Burst Installed SRAM Type: Burst Pipeline Burst Speed: Unknown Error Correction Type: Single-bit ECC System Type: Data Associativity: 4-way Set-associative Handle 0x0007, DMI type 7, 19 bytes Cache Information Socket Designation: L2 Cache for CPU#1 Configuration: Enabled, Not Socketed, Level 2 Operational Mode: Write Back Location: Internal Installed Size: 4096 KB Maximum Size: 4096 KB Supported SRAM Types: Burst Pipeline Burst Installed SRAM Type: Burst Speed: Unknown Error Correction Type: Single-bit ECC System Type: Unified Associativity: 4-way Set-associative Handle 0x0008, DMI type 7, 19 bytes Cache Information Socket Designation: L1 Cache for CPU#2 Configuration: Enabled, Not Socketed, Level 1 Operational Mode: Write Back Location: Internal Installed Size: 64 KB Maximum Size: 64 KB Supported SRAM Types: Burst Pipeline Burst Installed SRAM Type: Burst Pipeline Burst Speed: Unknown Error Correction Type: Single-bit ECC System Type: Data Associativity: 4-way Set-associative Handle 0x0009, DMI type 7, 19 bytes Cache Information Socket Designation: L2 Cache for CPU#2 Configuration: Enabled, Not Socketed, Level 2 Operational Mode: Write Back Location: Internal Installed Size: 4096 KB Maximum Size: 4096 KB Supported SRAM Types: Burst Pipeline Burst Installed SRAM Type: Burst Speed: Unknown Error Correction Type: Single-bit ECC System Type: Unified Associativity: 4-way Set-associative Handle 0x000A, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 1(Serial ICON) External Connector Type: DB-9 male Port Type: Serial Port 16550A Compatible Handle 0x000B, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 2(Serial ICON) External Connector Type: DB-9 male Port Type: Serial Port 16550A Compatible Handle 0x000C, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: (Keyboard ICON) External Connector Type: PS/2 Port Type: Keyboard Port Handle 0x000D, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: (Mouse ICON) External Connector Type: PS/2 Port Type: Mouse Port Handle 0x000E, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: IDE Internal Connector Type: On Board IDE External Reference Designator: (IDE ICON) External Connector Type: None Port Type: Other Handle 0x000F, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: SATA1 Internal Connector Type: Other External Reference Designator: 1(S-ATA ICON) External Connector Type: None Port Type: Other Handle 0x0010, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: SATA2 Internal Connector Type: Other External Reference Designator: 2(S-ATA ICON) External Connector Type: None Port Type: Other Handle 0x0011, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: SAS1 Internal Connector Type: Other External Reference Designator: 1(SAS ICON) External Connector Type: None Port Type: Other Handle 0x0012, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: SAS2 Internal Connector Type: Other External Reference Designator: 2(SAS ICON) External Connector Type: None Port Type: Other Handle 0x0013, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 1(Network ICON) External Connector Type: RJ-45 Port Type: Network Port Handle 0x0014, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 2(Network ICON) External Connector Type: RJ-45 Port Type: Network Port Handle 0x0015, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 3(Network ICON) External Connector Type: RJ-45 Port Type: Network Port Handle 0x0016, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: USB1 Internal Connector Type: Other External Reference Designator: 1(USB ICON) External Connector Type: None Port Type: USB Handle 0x0017, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: USB2 Internal Connector Type: Other External Reference Designator: 2(USB ICON) External Connector Type: None Port Type: USB Handle 0x0018, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 3(USB ICON) External Connector Type: Access Bus (USB) Port Type: USB Handle 0x0019, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 4(USB ICON) External Connector Type: Access Bus (USB) Port Type: USB Handle 0x001A, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 5(USB ICON) External Connector Type: Access Bus (USB) Port Type: USB Handle 0x001B, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: 6(USB ICON) External Connector Type: Access Bus (USB) Port Type: USB Handle 0x001C, DMI type 8, 9 bytes Port Connector Information Internal Reference Designator: Not Specified Internal Connector Type: None External Reference Designator: (Video ICON) External Connector Type: DB-15 female Port Type: Video Port Handle 0x001D, DMI type 9, 13 bytes System Slot Information Designation: PCI-1b Type: 64-bit PCI-X Current Usage: Available Length: Long ID: 27 Characteristics: 3.3 V is provided PME signal is supported SMBus signal is supported Handle 0x001E, DMI type 9, 13 bytes System Slot Information Designation: PCI-2b Type: 64-bit PCI-X Current Usage: Available Length: Long ID: 43 Characteristics: 3.3 V is provided PME signal is supported SMBus signal is supported Handle 0x001F, DMI type 9, 13 bytes System Slot Information Designation: PCI-3b Type: x8 PCI Express Current Usage: In Use Length: Long Characteristics: Unknown Handle 0x0020, DMI type 9, 13 bytes System Slot Information Designation: PCI-1c Type: x8 PCI Express Current Usage: Available Length: Short Characteristics: Unknown Handle 0x0021, DMI type 9, 13 bytes System Slot Information Designation: PCI-2c Type: x4 PCI Express Current Usage: Available Length: Short Characteristics: Unknown Handle 0x0022, DMI type 9, 13 bytes System Slot Information Designation: PCI-3c Type: x4 PCI Express Current Usage: Available Length: Short Characteristics: Unknown Handle 0x0023, DMI type 10, 6 bytes On Board Device Information Type: Video Status: Enabled Description: VGA Handle 0x0024, DMI type 10, 6 bytes On Board Device Information Type: Ethernet Status: Enabled Description: LAN1 Handle 0x0025, DMI type 10, 6 bytes On Board Device Information Type: Ethernet Status: Enabled Description: LAN2 Handle 0x0026, DMI type 11, 5 bytes OEM Strings String 1: HWID=041A String 2: Bull_Product Handle 0x0027, DMI type 12, 5 bytes System Configuration Options Option 1: JBAT1: Close to clear CMOS Option 2: J_FRB3: Close to stop FRB3 Timer Option 3: J_RECOVERY: Close to run BIOS Recovery Option 4: J_PASSWORD: Close to clear Password Handle 0x0028, DMI type 13, 22 bytes BIOS Language Information Installable Languages: 5 en|US|iso8859-1 fr|FR|iso8859-1 de|DE|iso8859-1 es|ES|iso8859-1 it|IT|iso8859-1 Currently Installed Language: en|US|iso8859-1 Handle 0x0029, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Single-bit ECC Maximum Capacity: 48 GB Error Information Handle: No Error Number Of Devices: 12 Handle 0x002A, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 512 MB Form Factor: DIMM Set: 1 Locator: DIMM 11 Bank Locator: BANK 1 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: 80CE Serial Number: 070C4495 Asset Tag: Part Number: M395T6553CZ4-CE61 Handle 0x002B, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 512 MB Form Factor: DIMM Set: 1 Locator: DIMM 21 Bank Locator: BANK 1 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: 80CE Serial Number: 070C4393 Asset Tag: Part Number: M395T6553CZ4-CE61 Handle 0x002C, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 2 Locator: DIMM 31 Bank Locator: BANK 2 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x002D, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 2 Locator: DIMM 41 Bank Locator: BANK 2 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x002E, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 3 Locator: DIMM 12 Bank Locator: BANK 3 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x002F, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 3 Locator: DIMM 22 Bank Locator: BANK 3 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x0030, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 4 Locator: DIMM 32 Bank Locator: BANK 4 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x0031, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 4 Locator: DIMM 42 Bank Locator: BANK 4 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x0032, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 5 Locator: DIMM 13 Bank Locator: BANK 5 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x0033, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 5 Locator: DIMM 23 Bank Locator: BANK 5 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x0034, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 6 Locator: DIMM 33 Bank Locator: BANK 6 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x0035, DMI type 17, 27 bytes Memory Device Array Handle: 0x0029 Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 6 Locator: DIMM 43 Bank Locator: BANK 6 Type: DDR2 Type Detail: Synchronous Speed: 533 MHz (1.9 ns) Manufacturer: Serial Number: Asset Tag: Part Number: Handle 0x0036, DMI type 18, 23 bytes 32-bit Memory Error Information Type: OK Granularity: Unknown Operation: Unknown Vendor Syndrome: Unknown Memory Array Address: Unknown Device Address: Unknown Resolution: Unknown Handle 0x0037, DMI type 18, 23 bytes 32-bit Memory Error Information Type: OK Granularity: Unknown Operation: Unknown Vendor Syndrome: Unknown Memory Array Address: Unknown Device Address: Unknown Resolution: Unknown Handle 0x0038, DMI type 126, 23 bytes Inactive Handle 0x0039, DMI type 126, 23 bytes Inactive Handle 0x003A, DMI type 126, 23 bytes Inactive Handle 0x003B, DMI type 126, 23 bytes Inactive Handle 0x003C, DMI type 126, 23 bytes Inactive Handle 0x003D, DMI type 126, 23 bytes Inactive Handle 0x003E, DMI type 126, 23 bytes Inactive Handle 0x003F, DMI type 126, 23 bytes Inactive Handle 0x0040, DMI type 126, 23 bytes Inactive Handle 0x0041, DMI type 126, 23 bytes Inactive Handle 0x0042, DMI type 19, 15 bytes Memory Array Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0003FFFFFFF Range Size: 1 GB Physical Array Handle: 0x0029 Partition Width: 0 Handle 0x0043, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00000000000 Ending Address: 0x0001FFFFFFF Range Size: 512 MB Physical Device Handle: 0x002A Memory Array Mapped Address Handle: 0x0042 Partition Row Position: 1 Handle 0x0044, DMI type 20, 19 bytes Memory Device Mapped Address Starting Address: 0x00020000000 Ending Address: 0x0003FFFFFFF Range Size: 512 MB Physical Device Handle: 0x002B Memory Array Mapped Address Handle: 0x0042 Partition Row Position: 1 Handle 0x0045, DMI type 126, 19 bytes Inactive Handle 0x0046, DMI type 126, 19 bytes Inactive Handle 0x0047, DMI type 126, 19 bytes Inactive Handle 0x0048, DMI type 126, 19 bytes Inactive Handle 0x0049, DMI type 126, 19 bytes Inactive Handle 0x004A, DMI type 126, 19 bytes Inactive Handle 0x004B, DMI type 126, 19 bytes Inactive Handle 0x004C, DMI type 126, 19 bytes Inactive Handle 0x004D, DMI type 126, 19 bytes Inactive Handle 0x004E, DMI type 126, 19 bytes Inactive Handle 0x004F, DMI type 24, 5 bytes Hardware Security Power-On Password Status: Disabled Keyboard Password Status: Not Implemented Administrator Password Status: Disabled Front Panel Reset Status: Not Implemented Handle 0x0050, DMI type 32, 11 bytes System Boot Information Status: No errors detected Handle 0x0051, DMI type 38, 18 bytes IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA2 (I/O) Register Spacing: Successive Byte Boundaries Interrupt Polarity: Active High Interrupt Trigger Mode: Edge Interrupt Number: b Handle 0x0052, DMI type 127, 4 bytes End Of Table