|
This is a short list of the Hardware configuration of a Bull Novascale R422 wich tested with Debian GNU/Linux 4.0 (etch). ( a status-list of the tested novascale´s). For a Installation-report look here |
CPU |
2x Intel® Xeon™ 3GHz Dualcore FSB1333, 4MB L2 Cache (2x2) |
Mainboard |
Intel Serverboard 5000VSA |
HDD |
2x160GB 7200rpm SATA2 |
Graphic |
ATI ES1000 (Onboard) |
RAM |
2GB FBD DDR2-667 |
Soundcard |
N/A |
Ethernet |
Intel® Corporation 82573E Gigabit Ethernet |
lspci
{{{ R422:~ # lspci 00:00.0 Host bridge:
- Intel Corporation 5000P Chipset Memory Controller Hub (rev b1)
00:02.0 PCI bridge:
- Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1)
00:04.0 PCI bridge:
- Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1)
00:06.0 PCI bridge:
- Intel Corporation 5000 Series Chipset PCI Express x8 Port 6-7 (rev b1)
00:08.0 System peripheral:
- Intel Corporation 5000 Series Chipset DMA Engine (rev b1)
00:10.0 Host bridge:
- Intel Corporation 5000 Series Chipset FSB Registers (rev b1)
00:10.1 Host bridge:
- Intel Corporation 5000 Series Chipset FSB Registers (rev b1)
00:10.2 Host bridge:
- Intel Corporation 5000 Series Chipset FSB Registers (rev b1)
00:11.0 Host bridge:
- Intel Corporation 5000 Series Chipset Reserved Registers (rev b1)
00:13.0 Host bridge:
- Intel Corporation 5000 Series Chipset Reserved Registers (rev b1)
00:15.0 Host bridge:
- Intel Corporation 5000 Series Chipset FBD Registers (rev b1)
00:16.0 Host bridge:
- Intel Corporation 5000 Series Chipset FBD Registers (rev b1)
00:1d.0 USB Controller:
- Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 09)
00:1d.1 USB Controller:
- Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 09)
00:1d.2 USB Controller:
- Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 (rev 09)
00:1d.7 USB Controller:
- Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 09)
00:1e.0 PCI bridge:
- Intel Corporation 82801 PCI Bridge (rev d9)
00:1f.0 ISA bridge:
- Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 09)
00:1f.2 IDE interface:
- Intel Corporation 631xESB/632xESB/3100 Chipset SATA Storage Controller IDE (rev 09)
00:1f.3 SMBus:
- Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller (rev 09)
01:00.0 PCI bridge:
- Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port (rev 01)
01:00.3 PCI bridge:
- Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge (rev 01)
02:00.0 PCI bridge:
- Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 (rev 01)
02:02.0 PCI bridge:
- Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E3 (rev 01)
04:00.0 Ethernet controller:
- Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) (rev 01)
04:00.1 Ethernet controller:
- Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) (rev 01)
08:01.0 VGA compatible controller:
- ATI Technologies Inc ES1000 (rev 02)
}}}
dmesg
r422deb:~# dmesg
Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 17:17:36 UTC 2007
BIOS-provided physical RAM map
BIOS-e820:
0000000000000000 - 000000000009e000 (usable)
BIOS-e820:
000000000009e000 - 00000000000a0000 (reserved)
BIOS-e820:
00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820:
0000000000100000 - 00000000cff60000 (usable)
BIOS-e820:
00000000cff60000 - 00000000cff69000 (ACPI data)
BIOS-e820:
00000000cff69000 - 00000000cff80000 (ACPI NVS)
BIOS-e820:
00000000cff80000 - 00000000d0000000 (reserved)
BIOS-e820:
00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820:
00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820:
00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820:
00000000ff000000 - 0000000100000000 (reserved)
BIOS-e820:
0000000100000000 - 0000000230000000 (usable)
Warning only 4GB will be used.
Use a PAE enabled kernel.
3200MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f6060
On node 0 totalpages: 1048576
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 819200 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6030
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0xcff64850
ACPI: FADT (v001 INTEL TUMWATER 0x06040000 PTL 0x00000003) @ 0xcff68e48
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0xcff68ebc
ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0xcff68f4c
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0xcff68f88
ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0xcff68fb0
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20050228) @ 0xcff6488c
ACPI: DSDT (v001 Intel BLAKFORD 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled)
Processor #6 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled)
Processor #7 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 2 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
Detected 3000.370 MHz processor.
Built 1 zonelists. Total pages: 1048576
Kernel command line: root=/dev/sda1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec80000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3365256k/4194304k available (1544k kernel code, 40780k reserved, 577k data, 196k init, 2489728k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 6004.63 BogoMIPS (lpj=12009268)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0004e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6000.63 BogoMIPS (lpj=12001261)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0004e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 2/6 eip 3000
Initializing CPU#2
Calibrating delay using timer specific routine.. 6000.70 BogoMIPS (lpj=12001417)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0004e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 3/7 eip 3000
Initializing CPU#3
Calibrating delay using timer specific routine.. 6000.71 BogoMIPS (lpj=12001437)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0004e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0004e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 06
Total of 4 processors activated (24006.69 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 4 CPUs: passed.
Brought up 4 CPUs
migration_cost=21,8967
checking if image is initramfs... it is
Freeing initrd memory: 4386k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
PCI: No mmconfig possible on 8:1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
Boot video device is 0000:08:01.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMD0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMD0.BPD2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 *7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:02:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:02:02.0
IO window: 2000-2fff
MEM window: d8000000-d80fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:01:00.0
IO window: 2000-2fff
MEM window: d8000000-d80fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:01:00.3
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
IO window: 2000-2fff
MEM window: d8000000-d81fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: d8200000-d82fffff
PREFETCH window: d0000000-d7ffffff
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:02:00.0 to 64
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:02:02.0 to 64
PCI: Setting latency timer of device 0000:01:00.3 to 64
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:04.0 to 64
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1184252656.596:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie01]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
PCI: Setting latency timer of device 0000:01:00.0 to 64
Allocate Port Service[0000:01:00.0:pcie10]
Allocate Port Service[0000:01:00.0:pcie11]
PCI: Setting latency timer of device 0000:02:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:02:00.0:pcie20]
Allocate Port Service[0000:02:00.0:pcie21]
PCI: Setting latency timer of device 0000:02:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:02:02.0:pcie20]
Allocate Port Service[0000:02:02.0:pcie21]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: Processor [CPU3] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x4
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x5
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x6
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x7
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:04:00.0 to 64
SCSI subsystem initialized
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
e1000: 0000:04:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:30:48:7b:24:a4
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:04:00.1[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:04:00.1 to 64
e1000: 0000:04:00.1: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:30:48:7b:24:a5
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
PCI: Enabling device 0000:00:1f.2 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1860 irq 14
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/133, 321672960 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
Vendor: ATA Model: WDC WD1600YS-01S Rev: 20.0
Type: Direct-Access ANSI SCSI revision: 05
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1868 irq 15
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0x177
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 17 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 50, io mem 0xd8500000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 17 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 50, io base 0x00001800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 233, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 177, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-6: new high speed USB device using ehci_hcd and address 3
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-6: configuration #1 chosen from 1 choice
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 3 ports detected
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
usb 2-1.1: new full speed USB device using uhci_hcd and address 3
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input0
usb 2-1.1: configuration #1 chosen from 1 choice
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
usbcore: registered new driver hiddev
input: Peppercon AG Multidevice as /class/input/input1
input: USB HID v1.01 Mouse [Peppercon AG Multidevice] on usb-0000:00:1d.7-6
input: Peppercon AG Multidevice as /class/input/input2
input: USB HID v1.01 Keyboard [Peppercon AG Multidevice] on usb-0000:00:1d.7-6
input: ALCOR macally Kbd Hub as /class/input/input3
input: USB HID v1.00 Keyboard [ALCOR macally Kbd Hub] on usb-0000:00:1d.0-1.1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 233
Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1 across:2650684k
EXT3 FS on sda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
dmidecode
# dmidecode 2.8
SMBIOS 2.4 present.
39 structures occupying 1261 bytes.
Table at 0xCFF6A000.
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Phoenix Technologies LTD
Version: 6.00
Release Date: 05/29/2007
Address: 0xE6530
Runtime Size: 105168 bytes
ROM Size: 1024 kB
Characteristics:
PCI is supported
PNP is supported
BIOS is upgradeable
BIOS shadowing is allowed
ESCD support is available
Boot from CD is supported
Selectable boot is supported
EDD is supported
3.5"/2.88 MB floppy services are supported (int 13h)
ACPI is supported
USB legacy is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
BIOS boot specification is supported
Targeted content distribution is supported
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Bull SAS
Product Name: NovaScale Universal
Version: R422
Serial Number: XAN-SM2P-00022
UUID: 53D19F64-D663-A017-8922-0030487B24A4
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Handle 0x0002, DMI type 2, 8 bytes
Base Board Information
Manufacturer: Supermicro
Product Name: X7DBT
Version: PCB Version
Serial Number: 0123456789
Handle 0x0003, DMI type 3, 17 bytes
Chassis Information
Manufacturer: Supermicro
Type: Other
Lock: Not Present
Version: 0123456789
Serial Number: 0123456789
Asset Tag:
Boot-up State: Safe
Power Supply State: Safe
Thermal State: Safe
Security Status: None
OEM Information: 0x00001234
Handle 0x0004, DMI type 4, 35 bytes
Processor Information
Socket Designation: LGA771/CPU1
Type: Central Processor
Family: Xeon
Manufacturer: Intel
ID: F6 06 00 00 FF FB EB BF
Signature: Type 0, Family 6, Model 15, Stepping 6
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Hyper-threading technology)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Intel(R) Xeon(R) CPU 5
Voltage: 1.4 V
External Clock: Unknown
Max Speed: 5000 MHz
Current Speed: 3000 MHz
Status: Populated, Enabled
Upgrade: Slot 1
L1 Cache Handle: 0x0006
L2 Cache Handle: 0x0007
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0005, DMI type 4, 35 bytes
Processor Information
Socket Designation: LGA771/CPU2
Type: Central Processor
Family: Xeon
Manufacturer: Intel
ID: F6 06 00 00 FF FB EB BF
Signature: Type 0, Family 6, Model 15, Stepping 6
Flags:
FPU (Floating-point unit on-chip)
VME (Virtual mode extension)
DE (Debugging extension)
PSE (Page size extension)
TSC (Time stamp counter)
MSR (Model specific registers)
PAE (Physical address extension)
MCE (Machine check exception)
CX8 (CMPXCHG8 instruction supported)
APIC (On-chip APIC hardware supported)
SEP (Fast system call)
MTRR (Memory type range registers)
PGE (Page global enable)
MCA (Machine check architecture)
CMOV (Conditional move instruction supported)
PAT (Page attribute table)
PSE-36 (36-bit page size extension)
CLFSH (CLFLUSH instruction supported)
DS (Debug store)
ACPI (ACPI supported)
MMX (MMX technology supported)
FXSR (Fast floating-point save and restore)
SSE (Streaming SIMD extensions)
SSE2 (Streaming SIMD extensions 2)
SS (Self-snoop)
HTT (Hyper-threading technology)
TM (Thermal monitor supported)
PBE (Pending break enabled)
Version: Intel(R) Xeon(R)
Voltage: 1.4 V
External Clock: Unknown
Max Speed: 5000 MHz
Current Speed: 3000 MHz
Status: Populated, Enabled
Upgrade: Slot 1
L1 Cache Handle: 0x0008
L2 Cache Handle: 0x0009
L3 Cache Handle: Not Provided
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0006, DMI type 7, 19 bytes
Cache Information
Socket Designation: L1 Cache
Configuration: Enabled, Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 16 KB
Maximum Size: 16 KB
Supported SRAM Types:
Burst
Pipeline Burst
Asynchronous
Installed SRAM Type: Asynchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0007, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2 Cache
Configuration: Enabled, Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 4096 KB
Maximum Size: 8192 KB
Supported SRAM Types:
Burst
Pipeline Burst
Asynchronous
Installed SRAM Type: Burst
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0008, DMI type 7, 19 bytes
Cache Information
Socket Designation: L1 Cache
Configuration: Enabled, Socketed, Level 1
Operational Mode: Write Back
Location: Internal
Installed Size: 16 KB
Maximum Size: 16 KB
Supported SRAM Types:
Burst
Pipeline Burst
Asynchronous
Installed SRAM Type: Asynchronous
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x0009, DMI type 7, 19 bytes
Cache Information
Socket Designation: L2 Cache
Configuration: Enabled, Socketed, Level 2
Operational Mode: Write Back
Location: Internal
Installed Size: 4096 KB
Maximum Size: 8192 KB
Supported SRAM Types:
Burst
Pipeline Burst
Asynchronous
Installed SRAM Type: Burst
Speed: Unknown
Error Correction Type: Unknown
System Type: Unknown
Associativity: Unknown
Handle 0x000A, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: JCOM1
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator: COM 1
External Connector Type: DB-9 male
Port Type: Serial Port 16550A Compatible
Handle 0x000B, DMI type 8, 9 bytes
Port Connector Information
Internal Reference Designator: JCOM2
Internal Connector Type: 9 Pin Dual Inline (pin 10 cut)
External Reference Designator: COM 2
External Connector Type: DB-9 male
Port Type: Serial Port 16550A Compatible
Handle 0x000C, DMI type 9, 13 bytes
System Slot Information
Designation: PCIE#1-x8
Type: Other
Current Usage: Available
Length: Other
Characteristics:
3.3 V is provided
Handle 0x000D, DMI type 11, 5 bytes
OEM Strings
String 1: Intel Dempsey/5000PX/ESB2
String 2: Supermicro motherboard-X7DBT
Handle 0x000E, DMI type 12, 5 bytes
System Configuration Options
Option 1: Jumper settings can be described here.
Handle 0x000F, DMI type 15, 29 bytes
System Event Log
Area Length: 32 bytes
Header Start Offset: 0x0000
Header Length: 16 bytes
Data Start Offset: 0x0010
Access Method: General-purpose non-volatile data functions
Access Address: 0x0000
Status: Valid, Not Full
Change Token: 0x0000004D
Header Format: Type 1
Supported Log Type Descriptors: 3
Descriptor 1: POST error
Data Format 1: POST results bitmap
Descriptor 2: Single-bit ECC memory error
Data Format 2: Multiple-event
Descriptor 3: Multi-bit ECC memory error
Data Format 3: Multiple-event
Handle 0x0010, DMI type 16, 15 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 64 GB
Error Information Handle: Not Provided
Number Of Devices: 8
Handle 0x0011, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x0010
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 1
Locator: DIMM x 2
Bank Locator: Bank1
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz (1.5 ns)
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0012, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x0010
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 1
Locator: DIMM x 2
Bank Locator: Bank2
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz (1.5 ns)
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0013, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x0010
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 1
Locator: DIMM x 2
Bank Locator: Bank3
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz (1.5 ns)
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0014, DMI type 17, 27 bytes
Memory Device
Array Handle: 0x0010
Error Information Handle: No Error
Total Width: 72 bits
Data Width: 64 bits
Size: 2048 MB
Form Factor: DIMM
Set: 1
Locator: DIMM x 2
Bank Locator: Bank4
Type: DDR2
Type Detail: Synchronous
Speed: 667 MHz (1.5 ns)
Manufacturer: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Part Number: Not Specified
Handle 0x0015, DMI type 19, 15 bytes
Memory Array Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x001FFFFFFFF
Range Size: 8 GB
Physical Array Handle: 0x0010
Partition Width: 0
Handle 0x0016, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00000000000
Ending Address: 0x0007FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x0011
Memory Array Mapped Address Handle: 0x0015
Partition Row Position: Unknown
Interleave Position: Unknown
Interleaved Data Depth: Unknown
Handle 0x0017, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00080000000
Ending Address: 0x000FFFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x0012
Memory Array Mapped Address Handle: 0x0015
Partition Row Position: Unknown
Interleave Position: Unknown
Interleaved Data Depth: Unknown
Handle 0x0018, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00100000000
Ending Address: 0x0017FFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x0013
Memory Array Mapped Address Handle: 0x0015
Partition Row Position: Unknown
Interleave Position: Unknown
Interleaved Data Depth: Unknown
Handle 0x0019, DMI type 20, 19 bytes
Memory Device Mapped Address
Starting Address: 0x00180000000
Ending Address: 0x001FFFFFFFF
Range Size: 2 GB
Physical Device Handle: 0x0014
Memory Array Mapped Address Handle: 0x0015
Partition Row Position: Unknown
Interleave Position: Unknown
Interleaved Data Depth: Unknown
Handle 0x001A, DMI type 23, 13 bytes
System Reset
Status: Enabled
Watchdog Timer: Present
Boot Option: Do Not Reboot
Boot Option On Limit: Do Not Reboot
Reset Count: Unknown
Reset Limit: Unknown
Timer Interval: Unknown
Timeout: Unknown
Handle 0x001B, DMI type 24, 5 bytes
Hardware Security
Power-On Password Status: Disabled
Keyboard Password Status: Unknown
Administrator Password Status: Disabled
Front Panel Reset Status: Unknown
Handle 0x001C, DMI type 25, 9 bytes
System Power Controls
Next Scheduled Power-on: 12-31 23:59:59
Handle 0x001D, DMI type 26, 20 bytes
Voltage Probe
Description: Voltage Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x001E, DMI type 27, 12 bytes
Cooling Device
Temperature Probe Handle: 0x001F
Type: Fan
Status: OK
OEM-specific Information: 0x00000000
Handle 0x001F, DMI type 28, 20 bytes
Temperature Probe
Description: Temperature Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x0020, DMI type 29, 20 bytes
Electrical Current Probe
Description: Electrical Current Probe
Location: Processor
Status: OK
Maximum Value: Unknown
Minimum Value: Unknown
Resolution: Unknown
Tolerance: Unknown
Accuracy: Unknown
OEM-specific Information: 0x00000000
Handle 0x0021, DMI type 30, 6 bytes
Out-of-band Remote Access
Manufacturer Name: Intel
Inbound Connection: Enabled
Outbound Connection: Disabled
Handle 0x0022, DMI type 32, 19 bytes
System Boot Information
Status: No errors detected
Handle 0x0023, DMI type 38, 18 bytes
IPMI Device Information
Interface Type: KCS (Keyboard Control Style)
Specification Version: 2.0
I2C Slave Address: 0x10
NV Storage Device: Not Present
Base Address: 0x0000000000000CA2 (I/O)
Register Spacing: Successive Byte Boundaries
Handle 0x0024, DMI type 126, 4 bytes
Inactive
Handle 0x0025, DMI type 127, 4 bytes
End Of Table
Handle 0x0026, DMI type 127, 4 bytes
End Of Table