Differences between revisions 15 and 16
Revision 15 as of 2017-08-17 16:08:47
Size: 6861
Editor: Diego Alonso
Comment: added spanish translation link
Revision 16 as of 2018-06-03 10:57:10
Size: 7004
Editor: ?SvetlanaTkachenko
Comment: added GraphicsCard, https://nouveau.freedesktop.org/wiki/Optimus/ (thanks shtrb)
Deletions are marked like this. Additions are marked like this.
Line 162: Line 162:
* [[Bumblebee|Bumblebee]]  * [[Bumblebee|Bumblebee]]
 * [[https://nouveau.freedesktop.org/wiki/Optimus/|Optimus at Nouveau wiki]] (this link is the recent X documentation )
 * [[GraphicsCard]]

Translation(s): English - español - Polski


NVIDIA Optimus

This page describes how to identify, configure and troubleshoot NVIDIA Optimus enabled systems for Debian. NVIDIA Optimus is a technology that enables dynamic, switchable graphics between the central processing unit's (CPU) embedded graphics capability and the discrete graphics processing unit (GPU) card. Due to the nature of this technology, various software components must be aware of, and configured for, the proper output of the display based on the user's desired configuration.

The instructions on this page apply to Debian Wheezy and newer.

* NVIDIA Optimus - http://www.nvidia.com/object/optimus_technology.html

Installation of Proprietary Graphics Driver Required

The instructions on this page assume that your system has already had the NVIDIA proprietary graphics drivers installed using the instructions, here: ?Driver Installation.

Identification

The quickest method to determine if your device uses an Optimus card is to search against the documented list on NVIDIA's website. Obtain the NVIDIA GPU identifier of your card with:

$ lspci | grep 3D

Compare the identifier (i.e. GeForce 7XXM, 8XXM, 9XXM) with the list, here: http://www.geforce.com/hardware/technology/optimus/supported-gpus

Also note the PCI identifier of the card, which is the 5-digit ID at the beginning of the previous command's output, XX:XX.X.

Configuration

Configuration of an NVIDIA Optimus enabled system can be somewhat complex, depending upon the desired end state. This section mentions and details a few of the more common configuration scenarios and how to adjust your Debian installation, accordingly.

Dynamic Graphics Disabled - BIOS

Rather than enabling the power saving features of dynamic, "switchable" graphics, one can simply configure the system to output to the local display using only a single graphics provider.

The simplest method of setting the graphics provider, if your hardware supports it, is to manually select the embedded CPU or NVIDIA GPU as the display provider in the system's BIOS. Of course, this is vendor specific and you must consult your hardware manufacturer's documentation for further detail.

Dynamic Graphics Disabled - xrandr and Display Manager Scripts

If your system does not support or provide a BIOS switch, an alternative is to configure X to output through the desired source to the system's attached screen. While this configuration does not take advantage of Optimus' power saving features, it can ensure a consistent desktop graphics experience for 3D applications.

1. Ensure xrandr is installed and available

# apt-get install x11-xserver-utils

2. Modify or create (if one doesn't exist) an xorg.conf under /etc/X11/xorg.conf; add the following:

Section "Module"
    Load "modesetting"
EndSection

Section "Device"
    Identifier "nvidia"
    Driver "nvidia"
    BusID "PCI:X:Y:Z"
    Option "AllowEmptyInitialConfiguration"
EndSection

# Insert any additional custom configurations, below:

Where "BusID" X:Y:Z are the shortened/truncated numbers from the ID gathered above. For example, if the output of lspci displayed a PCI ID of 09:00.0, the BusID entry would read: BusID "9:0:0"

3. Add/create a custom script, /usr/local/bin/switch_nvidia.sh:

xrandr --setprovideroutputsource modesetting NVIDIA-0
xrandr --auto
xrandr --dpi 96

The DPI setting, (--dpi) should be fine for most screens; however, this may need to be adjusted for newer high density pixel screens. Systems with HiDPI screens likely will want to set this to 192. Consult your hardware manufacturer's specification for the appropriate setting.

4. Make the script executable:

# chmod +x /usr/local/bin/switch_nvidia.sh

5. Configure your desired display manager to use a setup script during display setup.

Configure LightDM

1. Modify lightdm's configuration and add (if one doesn't already exist) a SeatDefaults section & script config:

[SeatDefaults]
display-setup-script=/usr/local/bin/switch_nvidia.sh

On default Jessie installations, this section will not exist and will need to be added in by hand.

2. Restart lightdm to apply the new configuration and allow lightdm to start X sessions with the NVIDIA card as the source:

Jessie and newer:

# systemctl restart lightdm.service

Wheezy:

# service lightdm restart

Configure GNOME Display Manager (GDM)

1. Create a two new .desktop files - /usr/share/gdm/greeter/autostart/optimus.desktop and /etc/xdg/autostart/optimus.desktop about following content:

[Desktop Entry]
Type=Application
Name=Optimus
Exec=sh -c "xrandr --setprovideroutputsource modesetting NVIDIA-0; xrandr --auto"
NoDisplay=true
X-GNOME-Autostart-Phase=DisplayServer

2. Restart GNOME Display Manager (GDM):

Jessie and newer:

# systemctl restart gdm3.service

Wheezy:

# service gdm3 restart

3. If NVIDIA driver still won't working, you can try use GNOME on Wayland display manager.

Content based on https://wiki.archlinux.org/index.php/NVIDIA_Optimus#GDM.

Configure KDE Display Manager (KDM)

TODO

Dynamic Graphics with Bumblebee

The proprietary NVIDIA graphics driver can also be used to enable dynamic graphics switching between the embedded and discrete graphics providers through the use of Bumblebee. This method takes advantage of Optimus' power saving features, but can be more complex to successfully enable offloaded 3D applications.

Checking drivers

You can check if installed drivers support 3D OpenGL graphics by executing following command:

$ glxinfo | grep OpenGL

Hybrid GPUs

If you have a hybrid GPU and installed bumblebee driver you can check it for Intel:

$ glxinfo | grep OpenGL

And for NVIDIA:

$ optirun glxinfo | grep OpenGL

Also very recommended is checking displaying 3D OpenGL graphics by running glxgears program.

Troubleshooting

TODO

See also


CategoryHardware | GraphicsCard | NvidiaGraphicsDrivers