Translation(s): none

(!) ?Discussion

DebianOn is an effort to document how to install, configure and use Debian on some specific hardware. Therefore potential buyers would know if that hardware is supported and owner would know how get the best out of that hardware.

The purpose is not to duplicate the Debian Official Documentation, but to document how to install Debian on some specific hardware.

Models covered
Dell ?PowerEdge 2950

Video card: ATI Technologies Inc ES1000
Network card: Broadcom Corporation ?NetXtreme II BCM5708 Gigabit Ethernet
CPU: Intel(R) Xeon(R) E5410 (?QuadCore @ 2.33GHz)
RAM: 4GB DDR2 667Mhz

Overall Status

Installation works perfectly fine!

Core Components

../lenny/photo.png

Boot Standard Kernel:

[ {OK} ]

LAN network card:

[ {OK} ]

Detect CD/DVD:

[ {OK} ]

Detect hard drives:

[ {OK} ]

Extra Features

CPU Frequency Scaling

[?]

Hibernation

[-]

Sleep / Suspend

[-]

Xorg

[-]

- OpenGL

[-]

- Resize-and-Rotate(randr)

[-]

Switch to External Screen

[-]

Mouse

- Built-in (Trackpoint)

[-]

- Built-in (Touchpad)

[-]

Modem

[-]

Wireless/Wifi

[-]

Keyboard's Hotkeys

[-]

Legend :
{OK} = OK ; {X} Unsupported(No Driver) ; /!\ = Error (Couldn't get it working); [?] Unknown, Not Test ; [-] Not-applicable
{i} = Configuration Required; X-( = Only works with a proprietary driver


System Summary

lspci

00:00.0 Host bridge [0600]: Intel Corporation 5000X Chipset Memory Controller Hub [8086:25c0] (rev 12)
00:02.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 2 [8086:25e2] (rev 12)
00:03.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 [8086:25e3] (rev 12)
00:04.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 [8086:25f8] (rev 12)
00:05.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 [8086:25e5] (rev 12)
00:06.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x8 Port 6-7 [8086:25f9] (rev 12)
00:07.0 PCI bridge [0604]: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 [8086:25e7] (rev 12)
00:10.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev 12)
00:10.1 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev 12)
00:10.2 Host bridge [0600]: Intel Corporation 5000 Series Chipset Error Reporting Registers [8086:25f0] (rev 12)
00:11.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f1] (rev 12)
00:13.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset Reserved Registers [8086:25f3] (rev 12)
00:15.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f5] (rev 12)
00:16.0 Host bridge [0600]: Intel Corporation 5000 Series Chipset FBD Registers [8086:25f6] (rev 12)
00:1c.0 PCI bridge [0604]: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 [8086:2690] (rev 09)
00:1d.0 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 [8086:2688] (rev 09)
00:1d.1 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 [8086:2689] (rev 09)
00:1d.2 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 [8086:268a] (rev 09)
00:1d.3 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 [8086:268b] (rev 09)
00:1d.7 USB Controller [0c03]: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller [8086:268c] (rev 09)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev d9)
00:1f.0 ISA bridge [0601]: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller [8086:2670] (rev 09)
00:1f.1 IDE interface [0101]: Intel Corporation 631xESB/632xESB IDE Controller [8086:269e] (rev 09)
01:00.0 RAID bus controller [0104]: LSI Logic / Symbios Logic SAS1078 PCI-X Fusion-MPT SAS [1000:0060] (rev 04)
02:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge [1166:0103] (rev c3)
03:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet [14e4:164c] (rev 12)
04:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port [8086:3500] (rev 01)
04:00.3 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge [8086:350c] (rev 01)
05:00.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 [8086:3510] (rev 01)
05:01.0 PCI bridge [0604]: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E2 [8086:3514] (rev 01)
06:00.0 PCI bridge [0604]: Broadcom EPB PCI-Express to PCI-X Bridge [1166:0103] (rev c3)
07:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet [14e4:164c] (rev 12)
0e:0d.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000 [1002:515e] (rev 02)

dmesg

Bootdata ok (command line is root=/dev/sda1 ro )
Linux version 2.6.18-6-amd64 (Debian 2.6.18.dfsg.1-18etch1) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Sun Feb 10 17:50:19 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
 BIOS-e820: 0000000000100000 - 00000000cfb50000 (usable)
 BIOS-e820: 00000000cfb50000 - 00000000cfb66000 (reserved)
 BIOS-e820: 00000000cfb66000 - 00000000cfb85c00 (ACPI data)
 BIOS-e820: 00000000cfb85c00 - 00000000d0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
DMI 2.5 present.
ACPI: RSDP (v002 DELL                                  ) @ 0x00000000000f21c0
ACPI: XSDT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000000f225c
ACPI: FADT (v003 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb83524
ACPI: MADT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb83078
ACPI: SPCR (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb83130
ACPI: HPET (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb83184
ACPI: MCFG (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb831c0
ACPI: WD__ (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb83200
ACPI: SLIC (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb83338
ACPI: ERST (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb6aaf4
ACPI: HEST (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb6ad04
ACPI: BERT (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb6a974
ACPI: EINJ (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb6a9a4
ACPI: TCPA (v001 DELL   PE_SC3   0x00000001 DELL 0x00000001) @ 0x00000000cfb834bc
ACPI: DSDT (v001 DELL   PE_SC3   0x00000001 INTL 0x20050624) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-0000000130000000
Bootmem setup node 0 0000000000000000-0000000130000000
On node 0 totalpages: 1029369
  DMA zone: 3057 pages, LIFO batch:0
  DMA32 zone: 832392 pages, LIFO batch:31
  Normal zone: 193920 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 7:7 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2 7:7 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1 7:7 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3 7:7 APIC version 20
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x15] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x17] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
SMP: Allowing 8 CPUs, 4 hotplug CPUs
Built 1 zonelists.  Total pages: 1029369
Kernel command line: root=/dev/sda1 ro
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 2327.507 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x166a000 - 0x566a000
Memory: 4040032k/4980736k available (1927k kernel code, 149088k reserved, 868k data, 176k init)
Calibrating delay using timer specific routine.. 4659.17 BogoMIPS (lpj=9318356)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM1)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 20781306
Detected 20.781 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x2
Initializing CPU#1
Calibrating delay using timer specific routine.. 4655.03 BogoMIPS (lpj=9310064)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 532 cycles)
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x1
Initializing CPU#2
Calibrating delay using timer specific routine.. 4655.74 BogoMIPS (lpj=9311488)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU2: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
CPU 2: Syncing TSC to CPU 0.
CPU 2: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 532 cycles)
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 4655.09 BogoMIPS (lpj=9310194)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 6144K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU3: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz stepping 06
CPU 3: Syncing TSC to CPU 0.
CPU 3: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 532 cycles)
Brought up 4 CPUs
testing NMI watchdog ... OK.
migration_cost=35,3887
checking if image is initramfs... it is
Freeing initrd memory: 4901k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:0e:0d.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2.UPST.DWN2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3.PE2P._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 *5 6 7 10 11 12)
ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid IPI0001
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0103
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
PCI-GART: No AMD northbridge found.
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:03' and the driver 'system'
pnp: match found with the PnP device '00:08' and the driver 'system'
pnp: 00:08: ioport range 0x800-0x87f could not be reserved
pnp: 00:08: ioport range 0x880-0x8bf has been reserved
pnp: 00:08: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x8e0-0x8e3 has been reserved
pnp: 00:08: ioport range 0x900-0x900 has been reserved
pnp: 00:08: ioport range 0xc00-0xc7f has been reserved
pnp: 00:08: ioport range 0xca0-0xca7 has been reserved
pnp: 00:08: ioport range 0xca9-0xcab has been reserved
pnp: match found with the PnP device '00:09' and the driver 'system'
pnp: 00:09: ioport range 0xca8-0xca8 has been reserved
pnp: 00:09: ioport range 0xcac-0xcac has been reserved
pnp: match found with the PnP device '00:0a' and the driver 'system'
PCI: Bridge: 0000:06:00.0
  IO window: disabled.
  MEM window: f4000000-f7ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:05:00.0
  IO window: disabled.
  MEM window: f4000000-f7ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:05:01.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.0
  IO window: disabled.
  MEM window: f4000000-f7ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.3
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
  IO window: disabled.
  MEM window: f2000000-f7ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
  IO window: e000-efff
  MEM window: fc300000-fc4fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:04.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:02:00.0
  IO window: disabled.
  MEM window: f8000000-fbffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: f8000000-fbffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: d000-dfff
  MEM window: fc100000-fc2fffff
  PREFETCH window: d8000000-dfffffff
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:04:00.0 to 64
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:05:00.0 to 64
PCI: Setting latency timer of device 0000:06:00.0 to 64
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:05:01.0 to 64
PCI: Setting latency timer of device 0000:04:00.3 to 64
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:03.0 to 64
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:04.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:02:00.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1209463077.300:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie01]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie01]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
PCI: Setting latency timer of device 0000:00:05.0 to 64
pcie_portdrv_probe->Dev[25e5:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
PCI: Setting latency timer of device 0000:00:07.0 to 64
pcie_portdrv_probe->Dev[25e7:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
Allocate Port Service[0000:00:07.0:pcie01]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:04:00.0 to 64
Allocate Port Service[0000:04:00.0:pcie10]
Allocate Port Service[0000:04:00.0:pcie11]
PCI: Setting latency timer of device 0000:05:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:05:00.0:pcie20]
Allocate Port Service[0000:05:00.0:pcie21]
PCI: Setting latency timer of device 0000:05:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:05:01.0:pcie20]
Allocate Port Service[0000:05:01.0:pcie21]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:06' and the driver 'serial'
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: match found with the PnP device '00:07' and the driver 'serial'
00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: the driver 'i8042 aux' has been registered
pnp: the driver 'i8042 kbd' has been unregistered
pnp: the driver 'i8042 aux' has been unregistered
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S4 S5)
Freeing unused kernel memory: 176k freed
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x5
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x6
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x7
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x8
SCSI subsystem initialized
megasas: 00.00.03.01 Sun May 14 22:49:52 PDT 2006
megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
USB Universal Host Controller Interface driver v3.0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
scsi0 : LSI Logic SAS based MegaRAID driver
  Vendor: ATA       Model: WDC WD2500YS-18S  Rev: 6C07
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: WDC WD2500YS-18S  Rev: 6C07
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: WDC WD2500YS-18S  Rev: 6C07
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: WDC WD2500YS-18S  Rev: 6C07
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: DP        Model: BACKPLANE         Rev: 1.05
  Type:   Enclosure                          ANSI SCSI revision: 05
  Vendor: DELL      Model: PERC 6/i          Rev: 1.11
  Type:   Direct-Access                      ANSI SCSI revision: 05
GSI 17 sharing vector 0x42 and IRQ 17
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 66, io base 0x0000cce0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI device sda: 974127104 512-byte hdwr sectors (498753 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 974127104 512-byte hdwr sectors (498753 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 00 08
SCSI device sda: drive cache: write back
 sda: sda1 sda2
sd 0:2:0:0: Attached scsi disk sda
GSI 18 sharing vector 0x4A and IRQ 18
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 20 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 74, io base 0x0000ccc0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 66, io base 0x0000cca0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 20 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 74, io base 0x0000cc80
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 66, io mem 0xfc500400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
ESB2: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 169
ESB2: chipset revision 9
ESB2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
usb 5-5: new high speed USB device using ehci_hcd and address 3
usb 5-5: configuration #1 chosen from 1 choice
hub 5-5:1.0: USB hub found
hub 5-5:1.0: 4 ports detected
hda: HL-DT-ST GCR-8240N, ATAPI CD/DVD-ROM drive
usb 2-1: new low speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Cherry GmbH as /class/input/input0
input: USB HID v1.11 Keyboard [Cherry GmbH] on usb-0000:00:1d.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.44 (August 10, 2006)
ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 16 (level, low) -> IRQ 169
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001e4f2ed4e0
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001e4f2ed4de
hda: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
intel_rng: FWH not detected
input: PC Speaker as /class/input/input1
floppy0: no floppy controllers found
Adding 2682844k swap on /dev/sda2.  Priority:-1 extents:1 across:2682844k
EXT3 FS on sda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
bnx2: eth0: using MSI
bnx2: eth0 NIC Link is Up, 100 Mbps full duplex, receive & transmit flow control ON
ACPI: Power Button (FF) [PWRF]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver

lsusb

lsusb -v | grep -E '\<(Bus|iProduct|bDeviceClass|bDeviceProtocol)' 2>/dev/null

Bus 005 Device 003: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0 "TetraHub"
  bDeviceClass            9 Hub
  bDeviceProtocol         2 TT per port
  iProduct                0
  bDeviceClass            9 Hub
  bDeviceProtocol         0 Full speed hub
Bus 005 Device 001: ID 0000:0000
  bDeviceClass            9 Hub
  bDeviceProtocol         1 Single TT
  iProduct                2 EHCI Host Controller
Bus 004 Device 001: ID 0000:0000
  bDeviceClass            9 Hub
  bDeviceProtocol         0 Full speed hub
  iProduct                2 UHCI Host Controller
Bus 002 Device 001: ID 0000:0000
  bDeviceClass            9 Hub
  bDeviceProtocol         0 Full speed hub
  iProduct                2 UHCI Host Controller
Bus 003 Device 001: ID 0000:0000
  bDeviceClass            9 Hub
  bDeviceProtocol         0 Full speed hub
  iProduct                2 UHCI Host Controller
Bus 001 Device 001: ID 0000:0000
  bDeviceClass            9 Hub
  bDeviceProtocol         0 Full speed hub
  iProduct                2 UHCI Host Controller

USB Host controllers entries (without OHCI, UHCI, EHCI) are removed too.

dmidecode

# dmidecode 2.8
SMBIOS 2.5 present.
66 structures occupying 3399 bytes.
Table at 0xCFB9C000.

Handle 0xDA00, DMI type 218, 11 bytes
OEM-specific Type
        Header and Data:
                DA 0B 00 DA B2 00 17 00 0E 20 00

Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
        Vendor: Dell Inc.
        Version: 2.2.6
        Release Date: 02/05/2008
        Address: 0xF0000
        Runtime Size: 64 kB
        ROM Size: 1024 kB
        Characteristics:
                ISA is supported
                PCI is supported
                PNP is supported
                BIOS is upgradeable
                BIOS shadowing is allowed
                ESCD support is available
                Boot from CD is supported
                Selectable boot is supported
                EDD is supported
                Japanese floppy for Toshiba 1.2 MB is supported (int 13h)
                5.25"/360 KB floppy services are supported (int 13h)
                5.25"/1.2 MB floppy services are supported (int 13h)
                3.5"/720 KB floppy services are supported (int 13h)
                Print screen service is supported (int 5h)
                8042 keyboard services are supported (int 9h)
                Serial services are supported (int 14h)
                Printer services are supported (int 17h)
                CGA/mono video services are supported (int 10h)
                ACPI is supported
                USB legacy is supported
                BIOS boot specification is supported
                Function key-initiated network boot is supported
                Targeted content distribution is supported
        BIOS Revision: 2.6

Handle 0x0100, DMI type 1, 27 bytes
System Information
        Manufacturer: Dell Inc.
        Product Name: PowerEdge 2950
        Version: Not Specified
        Serial Number:  
        UUID:  
        Wake-up Type: Power Switch
        SKU Number: Not Specified
        Family: Not Specified

Handle 0x0200, DMI type 2, 9 bytes
Base Board Information
        Manufacturer: Dell Inc.
        Product Name: 0CX396
        Version: A00
        Serial Number: .. .

Handle 0x0300, DMI type 3, 21 bytes
Chassis Information
        Manufacturer: Dell Inc.
        Type: Rack Mount Chassis
        Lock: Present
        Version: Not Specified
        Serial Number: 25GYM3J
        Asset Tag: Not Specified
        Boot-up State: Safe
        Power Supply State: Safe
        Thermal State: Safe
        Security Status: Unknown
        OEM Information: 0x00000000
        Heigth: 2 U
        Number Of Power Cords: Unspecified
        Contained Elements: 0

Handle 0x0400, DMI type 4, 40 bytes
Processor Information
        Socket Designation: CPU1
        Type: Central Processor
        Family: Xeon
        Manufacturer: Intel
        ID: 76 06 01 00 FF FB EB BF
        Signature: Type 0, Family 6, Model 23, Stepping 6
        Flags:
                FPU (Floating-point unit on-chip)
                VME (Virtual mode extension)
                DE (Debugging extension)
                PSE (Page size extension)
                TSC (Time stamp counter)
                MSR (Model specific registers)
                PAE (Physical address extension)
                MCE (Machine check exception)
                CX8 (CMPXCHG8 instruction supported)
                APIC (On-chip APIC hardware supported)
                SEP (Fast system call)
                MTRR (Memory type range registers)
                PGE (Page global enable)
                MCA (Machine check architecture)
                CMOV (Conditional move instruction supported)
                PAT (Page attribute table)
                PSE-36 (36-bit page size extension)
                CLFSH (CLFLUSH instruction supported)
                DS (Debug store)
                ACPI (ACPI supported)
                MMX (MMX technology supported)
                FXSR (Fast floating-point save and restore)
                SSE (Streaming SIMD extensions)
                SSE2 (Streaming SIMD extensions 2)
                SS (Self-snoop)
                HTT (Hyper-threading technology)
                TM (Thermal monitor supported)
                PBE (Pending break enabled)
        Version: Intel(R) Xeon(R) CPU           E5410  @ 2.33GHz
        Voltage: 1.4 V
        External Clock: 1333 MHz
        Max Speed: 3600 MHz
        Current Speed: 2333 MHz
        Status: Populated, Enabled
        Upgrade: <OUT OF SPEC>
        L1 Cache Handle: 0x0700
        L2 Cache Handle: 0x0701
        L3 Cache Handle: 0x0702
        Serial Number: Not Specified
        Asset Tag: Not Specified
        Part Number: Not Specified

Handle 0x0401, DMI type 4, 40 bytes
Processor Information
        Socket Designation: CPU2
        Type: Central Processor
        Family: Unknown
        Manufacturer: Intel
        ID: 00 00 00 00 00 00 00 00
        Version: Not Specified
        Voltage: 1.4 V
        External Clock: Unknown
        Max Speed: 3600 MHz
        Current Speed: Unknown
        Status: Unpopulated
        Upgrade: <OUT OF SPEC>
        L1 Cache Handle: 0x0703
        L2 Cache Handle: 0x0704
        L3 Cache Handle: 0x0705
        Serial Number: Not Specified
        Asset Tag: Not Specified
        Part Number: Not Specified

Handle 0x0700, DMI type 7, 19 bytes
Cache Information
        Socket Designation: Not Specified
        Configuration: Enabled, Not Socketed, Level 1
        Operational Mode: Write Back
        Location: Internal
        Installed Size: 128 KB
        Maximum Size: 128 KB
        Supported SRAM Types:
                Unknown
        Installed SRAM Type: Unknown
        Speed: Unknown
        Error Correction Type: Single-bit ECC
        System Type: Data
        Associativity: 8-way Set-associative

Handle 0x0701, DMI type 7, 19 bytes
Cache Information
        Socket Designation: Not Specified
        Configuration: Enabled, Not Socketed, Level 2
        Operational Mode: Write Back
        Location: Internal
        Installed Size: 12288 KB
        Maximum Size: 12288 KB
        Supported SRAM Types:
                Unknown
        Installed SRAM Type: Unknown
        Speed: Unknown
        Error Correction Type: Single-bit ECC
        System Type: Unified
        Associativity: Other

Handle 0x0702, DMI type 7, 19 bytes
Cache Information
        Socket Designation: Not Specified
        Configuration: Enabled, Not Socketed, Level 3
        Operational Mode: Write Back
        Location: Internal
        Installed Size: 0 KB
        Maximum Size: 0 KB
        Supported SRAM Types:
                Unknown
        Installed SRAM Type: Unknown
        Speed: Unknown
        Error Correction Type: Single-bit ECC
        System Type: Unified
        Associativity: Unknown

Handle 0x0703, DMI type 7, 19 bytes
Cache Information
        Socket Designation: Not Specified
        Configuration: Enabled, Not Socketed, Level 1
        Operational Mode: Write Back
        Location: Internal
        Installed Size: 0 KB
        Maximum Size: 16 KB
        Supported SRAM Types:
                Unknown
        Installed SRAM Type: Unknown
        Speed: Unknown
        Error Correction Type: Parity
        System Type: Data
        Associativity: <OUT OF SPEC>

Handle 0x0704, DMI type 7, 19 bytes
Cache Information
        Socket Designation: Not Specified
        Configuration: Enabled, Not Socketed, Level 2
        Operational Mode: Write Back
        Location: Internal
        Installed Size: 0 KB
        Maximum Size: 2048 KB
        Supported SRAM Types:
                Unknown
        Installed SRAM Type: Unknown
        Speed: Unknown
        Error Correction Type: Single-bit ECC
        System Type: Unified
        Associativity: <OUT OF SPEC>

Handle 0x0705, DMI type 7, 19 bytes
Cache Information
        Socket Designation: Not Specified
        Configuration: Enabled, Not Socketed, Level 3
        Operational Mode: Write Back
        Location: Internal
        Installed Size: 0 KB
        Maximum Size: 0 KB
        Supported SRAM Types:
                Unknown
        Installed SRAM Type: Unknown
        Speed: Unknown
        Error Correction Type: Single-bit ECC
        System Type: Unified
        Associativity: <OUT OF SPEC>

Handle 0x0800, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: DB-15 female
        Port Type: Video Port

Handle 0x0801, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: DB-15 female
        Port Type: Video Port

Handle 0x0802, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: Access Bus (USB)
        Port Type: USB

Handle 0x0803, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: Access Bus (USB)
        Port Type: USB

Handle 0x0804, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: Access Bus (USB)
        Port Type: USB

Handle 0x0805, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: Access Bus (USB)
        Port Type: USB

Handle 0x0806, DMI type 126, 9 bytes
Inactive

Handle 0x0807, DMI type 126, 9 bytes
Inactive

Handle 0x0808, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: Access Bus (USB)
        External Reference Designator: Not Specified
        External Connector Type: None
        Port Type: USB

Handle 0x0809, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: RJ-45
        Port Type: Network Port

Handle 0x080A, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: RJ-45
        Port Type: Network Port

Handle 0x080B, DMI type 8, 9 bytes
Port Connector Information
        Internal Reference Designator: Not Specified
        Internal Connector Type: None
        External Reference Designator: Not Specified
        External Connector Type: DB-9 male
        Port Type: Serial Port 16550A Compatible

Handle 0x0900, DMI type 9, 17 bytes
System Slot Information
        Designation: PCI1
        Type: x8 PCI Express
        Current Usage: Available
        Length: Long
        Characteristics:
                3.3 V is provided
                PME signal is supported

Handle 0x0901, DMI type 9, 17 bytes
System Slot Information
        Designation: PCI2
        Type: x8 PCI Express
        Current Usage: Available
        Length: Long
        Characteristics:
                3.3 V is provided
                PME signal is supported

Handle 0x0902, DMI type 9, 17 bytes
System Slot Information
        Designation: PCI3
        Type: x4 PCI Express
        Current Usage: Available
        Length: Long
        Characteristics:
                3.3 V is provided
                PME signal is supported

Handle 0x0903, DMI type 126, 17 bytes
Inactive

Handle 0x0904, DMI type 126, 17 bytes
Inactive

Handle 0x0905, DMI type 126, 17 bytes
Inactive

Handle 0x0A00, DMI type 10, 10 bytes
On Board Device 1 Information
        Type: Video
        Status: Enabled
        Description: Embedded ATI ES1000 Video
On Board Device 2 Information
        Type: Ethernet
        Status: Enabled
        Description: Embedded Broadcom 5708 NIC 1
On Board Device 3 Information
        Type: Ethernet
        Status: Enabled
        Description: Embedded Broadcom 5708 NIC 2

Handle 0x0B00, DMI type 11, 5 bytes
OEM Strings
        String 1: Dell System
        String 2: 5[0000]

Handle 0x7E00, DMI type 126, 154 bytes
Inactive

Handle 0x0C00, DMI type 12, 5 bytes
System Configuration Options
        Option 1: NVRAM_CLR:  Clear user settable NVRAM areas and set defaults
        Option 2: PWRD_EN:  Close to enable password

Handle 0x0D00, DMI type 13, 22 bytes
BIOS Language Information
        Installable Languages: 1
                en|US|iso8859-1
        Currently Installed Language: en|US|iso8859-1

Handle 0x1000, DMI type 16, 15 bytes
Physical Memory Array
        Location: System Board Or Motherboard
        Use: System Memory
        Error Correction Type: Multi-bit ECC
        Maximum Capacity: 32 GB
        Error Information Handle: Not Provided
        Number Of Devices: 8

Handle 0x1100, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: 2048 MB
        Form Factor: <OUT OF SPEC>
        Set: 1
        Locator: DIMM1
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: 667 MHz (1.5 ns)
        Manufacturer: 80CE7FB380CE
        Serial Number: 292A08AD
        Asset Tag: 010815
        Part Number: M395T5750EZ4-CE66

Handle 0x1101, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: 2048 MB
        Form Factor: <OUT OF SPEC>
        Set: 1
        Locator: DIMM2
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: 667 MHz (1.5 ns)
        Manufacturer: 80CE7FB380CE
        Serial Number: 292A0778
        Asset Tag: 010815
        Part Number: M395T5750EZ4-CE66

Handle 0x1102, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: No Module Installed
        Form Factor: <OUT OF SPEC>
        Set: 2
        Locator: DIMM3
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: Unknown
        Manufacturer:
        Serial Number:
        Asset Tag:
        Part Number:

Handle 0x1103, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: No Module Installed
        Form Factor: <OUT OF SPEC>
        Set: 2
        Locator: DIMM4
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: Unknown
        Manufacturer:
        Serial Number:
        Asset Tag:
        Part Number:

Handle 0x1104, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: No Module Installed
        Form Factor: <OUT OF SPEC>
        Set: 3
        Locator: DIMM5
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: Unknown
        Manufacturer:
        Serial Number:
        Asset Tag:
        Part Number:

Handle 0x1105, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: No Module Installed
        Form Factor: <OUT OF SPEC>
        Set: 3
        Locator: DIMM6
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: Unknown
        Manufacturer:
        Serial Number:
        Asset Tag:
        Part Number:

Handle 0x1106, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: No Module Installed
        Form Factor: <OUT OF SPEC>
        Set: 4
        Locator: DIMM7
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: Unknown
        Manufacturer:
        Serial Number:
        Asset Tag:
        Part Number:

Handle 0x1107, DMI type 17, 28 bytes
Memory Device
        Array Handle: 0x1000
        Error Information Handle: Not Provided
        Total Width: 72 bits
        Data Width: 64 bits
        Size: No Module Installed
        Form Factor: <OUT OF SPEC>
        Set: 4
        Locator: DIMM8
        Bank Locator: Not Specified
        Type: <OUT OF SPEC>
        Type Detail: Synchronous
        Speed: Unknown
        Manufacturer:
        Serial Number:
        Asset Tag:
        Part Number:

Handle 0x1108, DMI type 126, 28 bytes
Inactive

Handle 0x1109, DMI type 126, 28 bytes
Inactive

Handle 0x110A, DMI type 126, 28 bytes
Inactive

Handle 0x110B, DMI type 126, 28 bytes
Inactive

Handle 0x1300, DMI type 19, 15 bytes
Memory Array Mapped Address
        Starting Address: 0x00000000000
        Ending Address: 0x000CFFFFFFF
        Range Size: 3328 MB
        Physical Array Handle: 0x1000
        Partition Width: 0

Handle 0x1301, DMI type 19, 15 bytes
Memory Array Mapped Address
        Starting Address: 0x00100000000
        Ending Address: 0x0012FFFFFFF
        Range Size: 768 MB
        Physical Array Handle: 0x1000
        Partition Width: 0

Handle 0x2000, DMI type 32, 11 bytes
System Boot Information
        Status: No errors detected

Handle 0x2600, DMI type 38, 18 bytes
IPMI Device Information
        Interface Type: KCS (Keyboard Control Style)
        Specification Version: 2.0
        I2C Slave Address: 0x10
        NV Storage Device: Not Present
        Base Address: 0x0000000000000CA8 (I/O)
        Register Spacing: 32-bit Boundaries

Handle 0x2900, DMI type 41, 11 bytes
Unknown Type
        Header and Data:
                29 0B 00 29 01 85 01 00 00 03 00
        Strings:
                Embedded NIC 1

Handle 0x2901, DMI type 41, 11 bytes
Unknown Type
        Header and Data:
                29 0B 01 29 01 85 02 00 00 07 00
        Strings:
                Embedded NIC 2

Handle 0xD000, DMI type 208, 19 bytes
OEM-specific Type
        Header and Data:
                D0 13 00 D0 02 00 FE 00 B2 01 00 00 00 00 00 00
                00 00 02

Handle 0xD200, DMI type 210, 12 bytes
OEM-specific Type
        Header and Data:
                D2 0C 00 D2 F8 03 04 03 06 80 04 05

Handle 0xD400, DMI type 212, 127 bytes
OEM-specific Type
        Header and Data:
                D4 7F 00 D4 70 00 71 00 00 10 2D 2E 03 00 11 7F
                80 04 00 11 7F 00 42 00 11 FE 01 43 00 11 FE 00
                00 00 11 9F 20 00 00 11 9F 00 6E 01 11 9F 20 6D
                01 11 9F 00 31 40 11 FB 00 32 40 11 FB 04 9D 00
                11 FD 02 9E 00 11 FD 00 9F 00 26 FE 01 A0 00 26
                FE 00 51 00 26 3F 00 52 00 26 3F 40 53 00 26 3F
                80 54 00 26 3F C0 28 40 26 DF 20 29 40 26 DF 00
                D6 01 26 F7 00 D7 01 26 F7 08 FF FF 00 00 00

Handle 0xD401, DMI type 212, 207 bytes
OEM-specific Type
        Header and Data:
                D4 CF 01 D4 70 00 71 00 03 40 5A 6D 6B 00 78 7F
                80 6C 00 78 7F 00 58 00 78 FA 05 59 00 78 FA 00
                5C 00 78 BF 40 5D 00 78 BF 00 04 80 78 FD 02 01
                A0 78 FD 00 00 00 55 E7 00 00 00 55 E7 08 00 00
                55 E7 10 6C 01 57 FC 00 6B 01 57 FC 01 6A 01 57
                FC 02 77 01 54 FC 00 78 01 54 FC 01 79 01 54 FC
                02 7A 01 54 FC 03 33 40 54 CF 00 34 40 54 CF 10
                35 40 54 CF 20 36 40 54 CF 30 1A 40 54 FB 04 1B
                40 54 FB 00 1C 40 54 F7 08 1D 40 54 F7 00 43 40
                58 DF 20 42 40 58 DF 00 6E 00 58 FC 01 2D 00 58
                FC 02 DA 01 58 FC 03 2E 00 58 FC 00 22 40 58 EF
                10 23 40 58 EF 00 BB 00 58 F3 04 BC 00 58 F3 08
                DB 01 58 F3 0C BA 00 58 F3 00 FF FF 00 00 00

Handle 0xD402, DMI type 212, 47 bytes
OEM-specific Type
        Header and Data:
                D4 2F 02 D4 70 00 71 00 03 40 5A 6D D8 00 55 7F
                80 D9 00 55 7F 00 00 C0 5C 00 0A 03 C0 67 00 05
                83 00 76 00 00 84 00 77 00 00 FF FF 00 00 00

Handle 0xD403, DMI type 212, 247 bytes
OEM-specific Type
        Header and Data:
                D4 F7 03 D4 72 00 73 00 00 40 5D 5E 71 01 46 FB
                04 72 01 46 FB 00 73 01 46 F7 08 74 01 46 F7 00
                00 00 46 FE 00 00 00 46 FE 01 4A 01 46 BF 40 4B
                01 46 BF 00 D3 00 00 00 02 D4 00 02 00 02 00 90
                2C 00 00 01 90 2D 00 00 00 00 49 EB 14 DB 00 49
                EB 00 00 00 49 FC 00 00 00 49 FC 01 00 00 49 FC
                02 00 00 49 7F 00 00 00 49 7F 80 17 01 4A FE 00
                18 01 4A FE 01 19 01 4A FD 00 1A 01 4A FD 02 00
                00 4A FB 00 00 00 4A FB 04 00 00 4A F7 00 00 00
                4A F7 08 35 01 4B FC 00 37 01 4B FC 01 3B 01 4B
                F3 04 DE 00 63 FE 01 26 40 42 FE 01 27 40 42 FE
                00 49 01 47 FE 01 48 01 47 FE 00 A1 00 45 CF 20
                A3 00 45 CF 10 A2 00 45 CF 00 02 40 46 DF 00 01
                40 46 DF 20 00 00 7E FC 00 00 00 7E FC 01 00 00
                7E FC 02 00 00 7E F3 00 00 00 7E F3 04 00 00 7E
                F3 08 FF FF 00 00 00

Handle 0xD404, DMI type 212, 77 bytes
OEM-specific Type
        Header and Data:
                D4 4D 04 D4 72 00 73 00 00 40 5D 5E 41 40 40 FE
                01 40 40 40 FE 00 CF 01 40 FD 02 D0 01 40 FD 00
                45 40 40 F7 08 44 40 40 F7 00 FC 01 45 BF 00 FD
                01 45 BF 40 40 01 47 FD 02 41 01 47 FD 00 31 02
                47 FB 00 32 02 47 FB 04 FF FF 00 00 00

Handle 0xD405, DMI type 212, 27 bytes
OEM-specific Type
        Header and Data:
                D4 1B 05 D4 70 00 71 00 03 40 5A 6D 12 02 57 EF
                00 11 02 57 EF 10 FF FF 00 00 00

Handle 0xD800, DMI type 216, 9 bytes
OEM-specific Type
        Header and Data:
                D8 09 00 D8 01 02 01 00 00
        Strings:
                ATI
                RN50 A20 BIOS

Handle 0xDE00, DMI type 222, 16 bytes
OEM-specific Type
        Header and Data:
                DE 10 00 DE 01 04 FF FF 00 00 00 00 00 00 00 01

Handle 0x7F00, DMI type 127, 4 bytes
End Of Table

http://www.dell.com/content/products/productdetails.aspx/pedge_2950_3?c=us&cs=555&l=en&s=biz