This section describes how networking is setup by default in FreedomBox and how you can customize it. See also the ?Firewall section for more information on how firewall works.
In a fresh image of FreedomBox, network is not configured at all. When the image is written to an SD card and the device boots, configuration is done. During first boot, FreedomBox setup package detects the networks interfaces and tries to automatically configure them so that FreedomBox is available for further configuration via the web interface from another machine without the need to connect a monitor. Automatic configuration also tries to make FreedomBox useful, out of the box, for the most important scenarios FreedomBox is used for.
There are two scenarios it handles: when is a single ethernet interface and when there are multiple ethernet interfaces.
1. Single ethernet interface
When there is only single ethernet interface available on the hardware device, there is not much scope for it to play the role of a router. In this case, the device is assumed to be just another machine in the network. Accordingly, the only available interface is configured to be an internal interface in automatic configuration mode. This means that it connects to the Internet using the configuration provided by a router in the network and also makes all (internal and external) of its services available to all the clients on this network.
2. Multiple ethernet interface
When there are multiple ethernet interfaces available on the hardware device, the device can act as a router. The interfaces are then configured to perform this function.
The first network interface is configured to be an WAN or external interface in automatic configuration mode. This means that it connects to the Internet using network configuration provided by the Internet Service Provider (ISP). Only services that are meant to be provided across the entire Internet (external services) will be exposed on this interface. You must plug your Internet connection into the port of this ethernet interface. If you wish to continue to have your existing router manage the Internet connection for you, then plug a connection from your router to the port on this interface.
The remaining network interfaces are configured for the clients of a router. They are configured as LAN or internal interfaces in shared configuration mode. This means that all the services (both external and internal) services are provided to who ever connects on this interface. Further, the shared mode means that clients will be able to receive details of automatic network connection on this interface. Specifically, DHCP configuration and DNS servers are provided on this interface. The Internet connection available to the device using the first network interface will be shared with clients using this interface. This all means that you can connect your computers to this network interface and they will get automatically configured and will be able to access the Internet via the FreedomBox.
Currently, it is not very clear which interface will be come the WAN interface (and the remaining being LAN interfaces) although the assignment process is deterministic. So, it take a bit of trail and error to figure out which one is which. In future, for each device, this will be well documented.
3. Wi-Fi configuration
All Wi-Fi interfaces are configured to be LAN or internal interfaces in shared configuration mode. They are also configured to become Wi-Fi access points with following details.
Name of the access point will be FreedomBox plus the name of the interface (to handle the case where there are multiple of them).
Password for connecting to the interface will be freedombox123.
The above default configuration may not be fit for your setup. You can customize the configuration to suit your needs from the Networks area in the 'setup' section of the FreedomBox web interface.
1. PPPoE connections
If your ISP does not provide automatic network configuration via DHCP and requires you to connection via PPPoE. To configure PPPoE, remove any network connection existing on an interface and add a PPPoE connection. Here, optionally, provide the account username and password given by your ISP and activate the connection.
2. Connect to Internet via Wi-Fi
By default Wi-Fi devices attached during first boot will be configured as access points. They can be configured as regular Wi-Fi devices instead to connection to a local network or an existing Wi-Fi router. To do this, click on the Wi-Fi connection to edit it. Change the mode to Infrastructure instead of Access Point mode and IPv4 Addressing Method to Automatic (DHCP) instead of Shared mode. Then the SSID provided will mean the Wi-Fi network name you wish to connect to and passphrase will be the used to while making the connection.
3. Adding a new network device
When a new network device is added, network manager will automatically configure it. In most cases this will not work to your liking. Delete the automatic configuration created on the interface and create a new network connection. Select your newly added network interface in the add connection page.
Then set firewall zone to internal and external appropriately.
- You can configure the interface to connect to a network or provide network configuration to whatever machine connects to it.
- Similarly, if it is a Wi-Fi interface, you can configure it to become a Wi-FI access point or to connect to an existing access points in the network.
Manual Network Operation
FreedomBox automatically configures networks by default and provides a simplified interface to customize the configuration to specific needs. In most cases, manual operation is not necessary. The following steps describe how to manually operate network configuration in the event that a user finds FreedomBox interface to insufficient for task at hand or to diagnose a problem that FreedomBox does not identify.
On the command line interface:
To see the list of available network devices:
To see the list of configured connections:
To see the current status of a connection:
nmcli connection show '<conneciton_name>'
To see the current firewall zone assigned to a network interface:
nmcli connection show '<conneciton_name>' | grep zone
firewall-cmd --zone=internal --list=all firewall-cmd --zone=external --list=all
To create a new network connection:
nmcli con add con-name "<connection_name>" ifname "<interface>" type ethernet nmcli con modify "<connection_name>" connection.autoconnect TRUE nmcli con modify "<connection_name>" connection.zone internal
To change the firewall zone for a connection:
nmcli con modify "<connection_name>" connection.zone "<internal|external>"
For more information on how to use nmcli command, see its man page. Also for a full list of configuration settings and type of connections accepted by Network Manager see:
To see the current status of the firewall and manually operate it, see the ?Firewall section.