Work on supporting the 901 and other Atom-based models (1000, 1000H) has commenced. We have a source package for the atl1e ethernet driver at and are working on producing debs of this and rebuilding the installer to include them so that an ethernet-based install on these models will be possible.

A driver for the wireless hardware can be found at

Testing debian package for rt8260

[liable] We are working on supporting the rt8260 driver. A preliminary package can be downloaded from

This can be built with module-assistant or from the tarball it installs. The easiest way is a simple

"m-a prepare"

"m-a a-i rt8260"


[BenArmstrong] I am confused about what the following is about, Jonathan. We added atl1e to our installer. Why should you need to copy this module? I don't believe anyone else did ...

[?JonathanRockway] To actually install from the network, just boot from the image without the networking drivers and get the network drivers from a separate flash drive. I used this deb: to get the atl1e.ko. I loaded that with insmod on the installer console, then proceeded as normal. A while later, I had a fully-working debian system. If you upgrade the kernel to 2.6.26-1, you won't need to manually install the driver anymore. Hopefully an installer using this kernel will be built soon.

?JohnGoerzen has confirmed these things work on the 901:

Performance seems to be better than the Xandros install.

?ThijmenDeGooijer has confirmed these things to work on the 1000H:

?IvanSanchez reports:

This doesn't seem to work out-of-the-box:

Hints and Tips from empika


you need to

#apt-get install module-assistant

this should also install the kernel headers needed to build the wireless drive. next runn

#module-assistant auto-install linux-uvc

to install the right module for the webcam. afterwards run

#echo 1 > /proc/acpi/asus/camera

you should now have a working webcam, test it with Cheese :D


I followed the instructions on which links to this driver from Ralink, it has special eee-pc bits in and is ready to compile once extracted, just run make and make install in the source dir.

You need to edit /etc/acpi/actions/ and replace all instances of ath0 with ra0 and ath_pci with rt2860sta To get the wireless hotkey to display the correct message when on the OSD you need to edit /etc/acpi/actions/, find the line (around 35)

if grep -q ath0 /proc/net/wireless; then

and change it to

if grep -q ra0 /proc/net/wireless; then

network-manager-gnome didnt work for me, it did not give me the option to use WPA encryption so I installed Wicd which works pretty well most of the time. grab it from

follow the instructions on the download page and remove everything from /etc/network/interfaces bar

auto lo
iface lo inet loopback

wikd should be in your apps->internet menu, you can now run it and connect to wireless AP's!

hotkeys, osd and misc bits

run apt-get install aosd-cat to install the OSD display'er. you then need to edit /etc/default/eee-acpi-scripts and change the following lines ENABLE_OSD='no' to ENABLE_OSD='yes'

If you are not going to install the latest alsa driver to get the front mic working you can change

{{{VOLUME_LABEL='?LineOut' VOLUME_LABEL='iSpeaker'}}} to {{{VOLUME_LABEL='Master' VOLUME_LABEL='Headphones'}}}

See the section below about what to do if you are installing the latest alsa

Multiple monitors

this is detailed on another page but i had some issues getting the desktop to display over the two monitors so have pasted my xorg.conf and some more info below to help. Firstly install xrandr if its not already

#apt-get install xrandr

then edit /etc/default/eee-acpi-scripts, change the line COMBINED_DISPLAY_SWITCHES='--mode 640x480' to

COMBINED_DISPLAY_SWITCHES='--output VGA --auto --above LVDS'

next you need to edit your /etc/X11/xorg.conf here is my version

Section "InputDevice"
        Identifier      "Generic Keyboard"
        Driver          "kbd"
        Option          "XkbRules"      "xorg"
        Option          "XkbModel"      "pc105"
        Option          "XkbLayout"     "gb"

Section "InputDevice"
        Identifier      "Configured Mouse"
        Driver          "synaptics"
        Option          "CorePointer"
        Option          "SendCoreEvents"        "true"
        Option          "Device"        "/dev/input/mice"
        Option          "Protocol"      "auto-dev"
        Option          "HorizEdgeScroll"       "1"

Section "Device"
        Identifier      "Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller"
        Driver          "intel"
        BusID           "PCI:0:2:0"

Section "Monitor"
        Identifier      "Configured Monitor"
        Option          "DPMS"

Section "Screen"
        Identifier      "Default Screen"
        Device          "Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller"
        Monitor         "Configured Monitor"
        DefaultDepth    24
        SubSection      "Display"
                Depth   24
                Modes   "1024x600"
                #this is 1024 wide by 1368 high (768+600=1368)
                Virtual 1024 1368

restart X without your external monitor plugged in, hitting the hotkey (f+f5) should now activate your external monitor. if not you can debug issues by running


as a normal user (or a user that has permission to run x stuff), this will give you an output from which you can tell which monitors are plugged in. without external monitor plugged in

Screen 0: minimum 320 x 200, current 1024 x 600, maximum 1024 x 1368
VGA disconnected (normal left inverted right x axis y axis)
LVDS connected 1024x600+0+0 (normal left inverted right x axis y axis) 195mm x 113mm
   1024x600       60.0*+
   800x600        60.3
   640x480        59.9
TV disconnected (normal left inverted right x axis y axis)

with external monitor plugged in

Screen 0: minimum 320 x 200, current 1024 x 600, maximum 1024 x 1368
VGA connected (normal left inverted right x axis y axis)
   1024x768       60.0
   800x600        60.3
   640x480        59.9
LVDS connected 1024x600+0+0 (normal left inverted right x axis y axis) 195mm x 113mm
   1024x600       60.0*+
   800x600        60.3
   640x480        59.9
TV disconnected (normal left inverted right x axis y axis)

running the xrandr command with the options we specified in /etc/default/eee-acpi-scripts should also help you debug any problems

#xrandr --output VGA --auto --above LVDS

front mic

To get the front mic working you have to rebuild the alsa driver using the latest release candidate. grab it from here

next you need to unpack it somewhere like /usr/src/ then build it. you may want to backup your old driver first

/usr/lib/2.6.25-2-686/kernel/sounds/pci/hda/# cp snd-hda-intel.ko snd-hda-intel.ko.stock
/usr/src/alsa-driver-1.0.18rc1# ./configure --with-cards=hda-intel --with-options=all
/usr/src/alsa-driver-1.0.18rc1# make
/usr/src/alsa-driver-1.0.18rc1# make install
/usr/src/alsa-driver-1.0.18rc1# ./snddevices

im not sure if the last step is necessary but i ran it anyway.

you can verify your new driver with

/usr/lib/2.6.25-2-686/kernel/sounds/pci/hda/# ls -l

check that the date on the snd-hda-intel.ko is about the time you compiled it :)

your now you need to reboot.

after the reboot checkout your mixer settings with alsamixer or the gnome-volume-control, the channels have changed from the stock driver.

To get your hot keys to work again you need to edit /etc/default/eee-acpi-scripts and change the mixer labels to




you also need to add the line


this should get the volume keys working again.

To get the mute key to work you need to edit /etc/acpi/actions/ Comment out the line (around line number 50)

status=$(amixer get $VOLUME_LABEL | sed -n '/%/{s/.*\[\(on\|off\)\].*/\u\1/p;q}')

and add this line underneath it

status=$(amixer get $I_SWITCH_LABEL | sed -n 's/.*\[\(on\|off\)\].*/\1/;ta;d;:a;p;q')

further down in the '# Fn+F7 -- mute/unmute speakers' section comment out the line

amixer -q set $VOLUME_LABEL toggle

and add instead

amixer -q set $I_SWITCH_LABEL toggle

you should now be all set

a few more annoying things that ive found with the default install

*Iceweasle has an odd version of flash installed where the flash movies are replaced by 'play buttons', this stops a few things working i found. i found this thread which helped sort the issue, quit iceweasel if its running and remove the odd version of flash

#apt-get remove swfdec-mozilla
#aptitude keep-all

the apt-get remove will complain about removing gnome but this is aparently a pseudo package and it was safe for me to hit y. not sure what aptitude keep-all does but they suggest to run it so i did, nothing bad seemed to happen. Next grab the latest flash from adobe and install it to /usr/lib/iceweasel when asked. now restart iceweasel and flash should be working a treat.

The other thing that bugged me about iceweasel was that it doesnt have backspace set as go back in history as default. i like this and to get it working type about:config in the address bar, you will be warned about it being dangerous to mess with these options but we're brave right? use the filter to search for backspace, you should get 1 result back called browser.backspace_action, its value was set to 2, setting it to 0 will make it become a back key again.