12507
Comment:
|
12491
|
Deletions are marked like this. | Additions are marked like this. |
Line 103: | Line 103: |
The eeepc-acpi-source package is available in Debian unstable and shortly in testing, too. It builds an out-of-kernel module to support the Eee PC hotkeys. It was based on Asus's patched asus_acpi.c module, but doesn't conflict with standard Debian kernel packages. | The eeepc-acpi-source package is available in Debian unstable and testing. It builds an out-of-kernel module to support the Eee PC hotkeys. It was based on Asus's patched asus_acpi.c module, but doesn't conflict with standard Debian kernel packages. |
Translations: [:DebianEeePCFrench/HowTo/Install:French] [:DebianEeePCGerman/HowTo/Install:German]
Install lenny using native Debian kernel and modules
Although this method is still new and we have some kinks to work out, it's where we're heading, so we'd prefer if users would try it out and give us feedback. The old method, using the Xandros kernel and modules is retained below for reference purposes.
Preparation
You need a USB disk. Please download these files:
http://bbqsrc.net/eeepc/debian/sid-usb.img.gz (Note: 'sid' here refers to the distribution used to build the installer, not the target system, which is lenny)
- this image was mastered with the process outlined in ["DebianEeePC/HowTo/CustomInstaller"]
[http://nion.modprobe.de/eeepc/sid-usb.img.gz (faster mirror: modprobe.de, location: Germany)]
http://packages.debian.org/lenny/i386/atl2-modules-2.6.22-3-686/download
To prepare the USB disk, copy the image onto the drive:
gunzip sid-usb.img.gz dd if=sid-usb.img of=/dev/<YOUR-USB-DEVICE>
Note: <YOUR-USB-DEVICE> = the whole device, not a device partition (e.g. /dev/sdX NOT /dev/sdX1)
Now mount <YOUR-USB-DEVICE> and copy the atl2-modules onto it:
cp atl2-modules-2.6.22-3-686_2.6.22+1.0.40.4-9_i386.deb /PATH/OF/USB/DISK/
You may have noticed that you are using the entire device without a partition table. This works because the BIOS knows how to boot directly from FAT partitions. This boot mode is called "superfloppy" mode and is supported by the Eee PC BIOS for USB devices and SD cards.
Installation
Boot the eee and press <ESC> during the first screen. This lets you select which device to boot from.
The actual installation is very standard; if you're reading this, you almost certainly already know how to install Debian. It is fine to use ext3 as your filesystem, which is the default. See [http://wiki.eeeuser.com/ssd_write_limit] for a compelling argument that you're not going to kill your flash drive by the small percentage of extra writes that a journaling filesystem will add over the lifespan of the drive. You may wish to do without swap simply because it will save space on the relatively small SSD in the Eee. Also ["DebianEeePC/TipsAndTricks"] links to some tuning tips if after reading this article you're still concerned about write life-span.
Additional modules not yet in Debian kernels
Ethernet (atl2)
When you first get into the eeepc-debian install you’ll notice your NIC / Ethernet is not working. That’s because you haven’t loaded the driver yet.
Put the flashdrive into your eeepc and mount it:
mount /dev/<YOUR-USB-DEVICE> /media
- To know which device your USB disk is, look at the output of dmesg after you insert the USB disk.
Now install the kernel module:
cd /media Become root and invoke the following commands: dpkg -i atl2-modules-2.6.22-3-686_2.6.22+1.0.40.4-9_i386.deb modprobe atl2 dhclient cd umount /media
Madwifi
Install and configure module-assistant:
Become root and invoke the following commands: apt-get install module-assistant m-a prepare
Download and install this patched madwifi-source package:
wget http://people.debian.org/~synrg/debian-eeepc/madwifi-source_0.9.3.2-2+eee_i386.deb Become root and invoke the following command: dpkg -i madwifi-source_0.9.3.2-2+eee_i386.deb
Now you can use module-assistant to build and install a .deb package for the driver:
Become root and invoke the following commands: m-a a-i madwifi modprobe ath_pci
You may want to put the madwifi-source package on hold so that in any future upgrades it won't be overwritten.
If you are using sid, (or the lenny version gets bumped, which it is likely to soon) then m-a a-i will first check for a newer source package. This is obviously bad as it wont have the binary patch applied. Use 'm-a build' to make the modules and then install the debs it makes in /usr/src.
uvcvideo
The module source in lenny should work with module-assistant:
Become root and invoke the following commands: m-a a-i linux-uvc modprobe uvcvideo
Then test it's working by executing:
Become root and invoke the following command: apt-get install luvcview As normal user you can now make use of your web cam tool luvcview -f yuv
The camera is switched off by default after the installation. You can enable it in the BIOS, or by doing echo 1 > /proc/acpi/asus/camera. You should see messages about the camera being detected if you do dmesg | tail.
If you broke your webcam settings, use mplayer -fps 30 tv:// once to restore them.
eeepc_acpi
The eeepc-acpi-source package is available in Debian unstable and testing. It builds an out-of-kernel module to support the Eee PC hotkeys. It was based on Asus's patched asus_acpi.c module, but doesn't conflict with standard Debian kernel packages.
First, set up a module-compilation environment as described in the Madwifi section above. Then build and install the eeepc-acpi module with module-assistant:
Become root and invoke the following commands: m-a a-i eeepc-acpi modprobe eeepc_acpi /etc/init.d/acpid restart
Add eeepc_acpi to /etc/modules so that it will be loaded when you boot.
Notes:
- The battery info is not very precise (jumps from 10% to 100%, no rate information, etc...). Apparently, this is normal. It appears that the userspace battery utilities expect the battery to report mAh, but in fact it reports percentage. This is either a bug in the battery firmware or a bug in the BIOS. In either case, unless someone comes up with a patch to deal with batteries that report percentage, Asus needs to fix this.
- Suspend does not yet work out of the box. See the solution given below using the "zzz" script.
Xorg
Touchpad Scrolling
The default debian installer did not enable the touchpad scrolling for me. The following are bits that I had to add to xorg.conf to enable touchpad scrolling.
Section "InputDevice" Identifier "Synaptics Touchpad" Driver "synaptics" Option "CorePointer" Option "SendCoreEvents" "true" Option "Device" "/dev/input/mice" Option "Protocol" "auto-dev" Option "HorizEdgeScroll" "1" EndSection Section "Server Layout" Identifier "Default Layout" Screen "Default Screen" InputDevice "Generic Keyboard" InputDevice "Synaptics Touchpad" EndSection
This will enable horizontal as well as vertical scrolling on the touchpad. By default, iceweasel will use the horizontal scrolling as <backwords/forwards> To disable this, go into about:config and change the following values.
mousewheel.horizscroll.withnokey.action (change 2 to 0) mousewheel.horizscroll.withnokey.numlines (change -1 to 1)
Aiglx support for compiz
The following were needed to get compiz working. Compiz works for me with xfce, but its a bit choppy rotating the cube to a workspace that has opened programs on it. (If you have a good working xorg.conf thats different to this, please update)
Section "Device" Identifier "Configured Video Device" Driver "i810" Option "XAANoOffscreenPixmaps" Option "AddARGBGLXVisuals" "true" EndSection Section "DRI" Mode 0666 Endsection Section "Extensions" Option "Composite" "Enable" Endsection
Troubleshooting
Forum
There is more information in this forum post (although some of it may be out of date):
http://forum.eeeuser.com/viewtopic.php?pid=47421#p47421
Ethernet (atl2)
Building from source
Become root and invoke the following commands: apt-get install module-assistant m-a a-i atl2 modprobe atl2
For good measure this reloads the atl2 driver.
Ethernet
One problem you may come across is the ethernet not becoming active. This is a bug with the chipset for when you install. To fix this, temporarily enable PXE/netboot in the BIOS. You may not come across this problem, but you can enable it and disable it at any time without problem. The problem will be gone as soon as you have installed so you may disable PXE in the BIOS after that.
Shutting down
There is an issue surrounding shutting down. The system halts, but the fan continues to run and the wifi light stays on. The reason is the sound module doesn't close correctly, but there is a fix!
- (as root) aptitude install acpi-support
- Edit /etc/default/acpi-support with your favourite text editor (or nano) and add snd_hda_intel to the MODULES="" line.
Then it will poweroff correctly!
[?FlorianGillig] don't work for me, works only once per three times... EEE don't power off correctly.
Silence hdd errors caused by acpi-support
Become root and invoke the following command: sed -i s/DO_HDPARM=y/DO_HDPARM=n/ /etc/acpi/*/90-hdparm.sh
Special key
Specials keys |
||
Key |
Function |
Work, comment |
Fn + F1 |
sleep |
Yes |
Fn + F2 |
wifi |
Yes (read details below) |
Fn + F3 |
- light screen |
Yes |
Fn + F4 |
+ light screen |
Yes |
Fn + F5 |
Change screen |
No, nothing append |
Fn + F6 |
Task manager |
No, nothing append |
Fn + F7 |
disabled Sound |
no, nothing append |
Fn + F8 |
- sound |
no, nothing append |
Fn + F9 |
+ sound |
no, nothing append |
[?NicolasBoullis] Enabling/disabling the wifi works like plugging/unplugging the PCI Express wifi card. To ensure that it properly gets enabled when it is plugged, you need the pciehp kernel module. (And for some reason, it only works with the "pciehp_force=1" option.) Hence, just append "pciehp pciehp_force=1" to your /etc/modules, run "modprobe pciehp pciehp_force=1" (or reboot if you're a Windows fan) and be happy with your Fn + F2 key.
[BenArmstrong] The pciehp_force=1 option is not a valid option with linux kernel 2.6.24. In any event, I would not recommend putting module options in /etc/modules. That's what /etc/modprobe.d/ is for.
[vedawalter] a "dirty" way to make Fn F7 - F9 work (no OSD atm), http://walter.flightshop.de/files/eeepc/eeepc-acpi_001a.tar.gz
Microphone fix
If the microphone does not work by default. The following fixes that.
- Edit /etc/modprobe.d/alsa-base and add the line “options snd-hda-intel model=3stack-dig”
Screen resolution
Because the resolution screen is 800x480. Many applications exceed the screen. The best example is the Gnome application Evolution. I'm looking for a solution.
found see ["DebianEeePC/TipsAndTricks"]
OLD: Install using the Xandros kernel and modules
Instructions for installing Debian on the Eee PC using Kibobo's http://kibobo.free.fr/EEE/debian/usb/usb.img.gz which contains the Xandros kernel that ships with the Eee PC can be found here:
It is possible to get wireless and wired ethernet connections working using this method.
Unfortunately, the kernel and modules in kibobo's image are out of date because the Asus update site kibobo fetched them from is out of date. One way around this is to extract the P701.gz image file from the recovery CD, gunzip it, mount it loopback, chroot into the mount, install dpkg-repack from etch, and dpkg-repack each package, though that's a lot of work to ask a user to do. The old packages seem to work well enough for now.
There are some further notes here:
Don't use Andrew's wifi script, as it does not work when there are blanks in the essid, which is pretty common. Use this version instead:
http://people.debian.org/~synrg/debian-eeepc/wifi
If you use Andrew's zzz script, you need to edit /etc/acpi/events/lidbtn to call lid.sh instead of lidbtn.sh.
I have put an improved version of zzz here:
http://people.debian.org/~synrg/debian-eeepc/zzz
In particular, it preserves the display better than Andrew's original and doesn't force you back to vt7 (the X session) even if you were on a different vt when you put the machine to sleep.
FixMe: package a suspend solution using original Eee PC acpi and/or Andrew Kilpatrick's scripts as a guide.