Differences between revisions 11 and 12
Revision 11 as of 2008-04-14 17:21:40
Size: 9810
Editor: ?cmang
Comment:
Revision 12 as of 2008-04-14 17:28:31
Size: 10138
Editor: ?cmang
Comment:
Deletions are marked like this. Additions are marked like this.
Line 138: Line 138:
        Driver "i810"
        Option "XAANoOffscreenPixmaps"
        Driver "intel"
        BusID "PCI:0:2:0"
        Option "EnablePageFlip" "on"
        Option "AccelMethod" "EXA"
        Option "MigrationHeuristic" "greedy"
        Option "AccelDFS" "true"
        Option "DynamicClocks" "on"
        Option "ColorTiling" "on"
        Option "FBTexPercent" "95"
        Option "XAANoOffscreenPixmaps" "true"
Line 152: Line 160:
  * [cmang] When following the above instructions, I was unable to get any window borders and window management when starting Compiz. In addition to the above, I had to install the compizconfig-settings-manager package. Then I ran ccsm and made sure that the "Window Decoration" plug-in was enabled. I switched to the Intel driver, tho I do not know if this made a difference. I then had to start compiz with: compiz --replace cpp   * [cmang] When following the above instructions, I was unable to get any window borders and window management when starting Compiz. In addition to the above, I had to install the compizconfig-settings-manager package. Then I ran ccsm and made sure that the "Window Decoration" plug-in was enabled. I then had to start compiz with: compiz --replace cpp

?TableOfContents

Translations: [:DebianEeePCFrench/HowTo/Configure:French]

Repository

The new installer adds our ["DebianEeePC/Repository"] to your /etc/apt/sources.list automatically. This includes some packages required to take full advantage of hardware in the Eee PC which not yet suitable for inclusion in the official Debian archives.

Additional modules not yet in Debian kernels

Introduction to building out-of-kernel modules

The instructions below require you to install and compile module source packages using module-assistant. This can be done on your Eee PC, but will result in the installation of a lot of development tools that you might not otherwise need.

An alternative method is to do the installation and compilation of the modules on another Debian machine (one that is faster and has more disk space), and then install the resulting module packages on the Eee PC.

If you decide to go this route, refer to the manpage for module-assistant. You will need to run "m-a build ..." instead of "m-a auto-install ...". Note that if your Eee PC is running a different kernel version than your build machine, you will need to install the linux-headers and linux-kbuild packages corresponding to the Eee PC's kernel, and use the "-l" option to specify that version when you invoke module-assistant.

Once you have successfully built a module, copy the resulting .deb to the Eee PC and install it there with "dpkg -i ...".

Ethernet (atl2)

This just works now. The old version of our installer had a bug which required a manual install of atl2 after installation – this is now no longer required.

Wireless (madwifi)

This is installed automatically by the new installer. See ["DebianEeePC/HowTo/Wifi"] to set up wifi with or without encryption.

Webcam (uvcvideo)

The module source in Lenny should work with module-assistant:

Become root and invoke the following commands:

m-a a-i linux-uvc
modprobe uvcvideo

This won't work if you are using a 2.6.24 kernel. As noted in #[http://bugs.debian.org/463655 463655], the latest SVN revision of the driver works fine.

Then test it's working by executing:

Become root and invoke the following command:

apt-get install luvcview
As normal user you can now make use of your web cam tool
luvcview -f yuv

The camera is switched off by default after the installation. You can enable it in the BIOS, or by doing echo 1 > /proc/acpi/asus/camera. You should see messages about the camera being detected if you do dmesg | tail.

You need to have installed acpi for this (see below) – at least in lenny.

If you broke your webcam settings, use mplayer -fps 30 tv:// once to restore them.

Power management & hotkeys

Kernel module (eeepc-acpi)

The eeepc-acpi kernel module and eeepc-acpi-scripts are now installed automatically by the new kernel.

Notes:

  • The battery info is not very precise (jumps from 10% to 100%, no rate information, etc...). Apparently, this is normal. It appears that the userspace battery utilities expect the battery to report mAh, but in fact it reports percentage. This is either a bug in the battery firmware or a bug in the BIOS. In either case, unless someone comes up with a patch to deal with batteries that report percentage, Asus needs to fix this.
  • [?DamyanIvanov] Hibernation mostly works for me on current Sid with 2.6.24 kernel once I've set up swap (and following the hints from ["DebianEeePC/TipsAndTricks"]). There is some problem with the madwifi driver that does not recover completely, but I think it is not hibernate-related as I see the same behaviour after suspend/resume.

  • [SamMorris] suspend worked for me with 2.6.24 with the s3_bios and dpms_on quirks. I have sent a patch upstream to hal@lists.freedesktop.org and also filed [http://bugs.debian.org/469648 #469648].

Scripts (eeepc-acpi-scripts)

Special keys

Key

Function

Work, comment

Fn + F1

sleep

Yes

Fn + F2

wifi

Yes (read details below)

Fn + F3

- light screen

Yes

Fn + F4

+ light screen

Yes

Fn + F5

Change screen

Yes

Fn + F6

Task manager

No, nothing append

Fn + F7

disabled Sound

Yes

Fn + F8

- sound

Yes

Fn + F9

+ sound

Yes

Install the eeepc-acpi-scripts package to get the described functionality. This is now available in unstable and testing. Please note that this package conflicts with acpi-support. As root you must apt-get purge acpi-support. This removes all of the acpi-support scripts that would remain in /etc. If you do not follow this step you will cause conflicts.

Enabling/disabling the wifi works like plugging/unplugging the PCI Express wifi card. To ensure that it properly gets enabled when it is plugged, you need the pciehp kernel module. (And for some reason, it only works with the "pciehp_force=1" option.) Create a file /etc/modprobe.d/pciehp with 'options pciehp pciehp_force=1' in it and put 'pciehp' in /etc/modules. Then 'rmmod pciehp; modprobe pciehp'.

Read the doc in /usr/share/doc/eeepc-acpi-scripts/README.Debian and configure /etc/default/eeepc-acpi-scripts as needed.

Xorg

Touchpad Scrolling

The default debian installer did not enable the touchpad scrolling for me. The following are bits that I had to add to xorg.conf to enable touchpad scrolling.

Section "InputDevice"
        Identifier      "Synaptics Touchpad"
        Driver          "synaptics"
        Option          "CorePointer"
        Option          "SendCoreEvents"        "true"
        Option          "Device"                "/dev/input/mice"
        Option          "Protocol"              "auto-dev"
        Option          "HorizEdgeScroll"       "1"
EndSection
Section "Server Layout"
    Identifier          "Default Layout"
    Screen              "Default Screen"
    InputDevice         "Generic Keyboard"
    InputDevice         "Synaptics Touchpad"
EndSection


  • [?DavideAgnolazza] This didn't work for me. I used "?HorizScrollDelta" set to 1 and horizontal scrolling starts working. The vertical scrolling was working by default. The default xorg.conf it's a little different about the above, but for me it worked fine and I just modified the ?HorizScrollDelta option.


  • This will enable horizontal as well as vertical scrolling on the touchpad. By default, iceweasel will use the horizontal scrolling as <backwords/forwards> To disable this, go into about:config and change the following values.

mousewheel.horizscroll.withnokey.action   (change 2 to 0)
mousewheel.horizscroll.withnokey.numlines  (change -1 to 1)

Display resolution and desktop size

In /etc/X11/xorg.conf, make sure any "?HorizSync" and "?VertRefresh" lines are commented out or removed from the "Monitor" section and set "Virtual 2048 2048" in the "Display" subsection of your "Screen" section, e.g.

Section "Monitor"
        Identifier      "Generic Monitor"
        Option          "DPMS"
EndSection

Section "Screen"
        Identifier      "Default Screen"
        Device          "Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller"
        Monitor         "Generic Monitor"
        DefaultDepth    24
        SubSection "Display"
                Depth           24
                Virtual         2048 2048
        EndSubSection
EndSection

Multiple displays

If you plug in an external display and press Fn-F5, the desktop is shared between the LCD and external display by default.

If you want, instead, to have one big desktop with the external display positioned above the Eee's own display, edit /etc/default/eeepc-acpi-scripts and set COMBINED_DISPLAY_SWITCHES="--above LVDS --auto".

Aiglx support for compiz

The following were needed to get [http://compiz.org/ Compiz] working. Compiz works for me with xfce, but its a bit choppy rotating the cube to a workspace that has opened programs on it. (If you have a good working xorg.conf thats different to this, please update)

Section "Device"
        Identifier      "Configured Video Device"
        Driver          "intel"
        BusID           "PCI:0:2:0"
        Option          "EnablePageFlip"    "on"   
        Option          "AccelMethod"        "EXA"
        Option          "MigrationHeuristic"   "greedy"
        Option          "AccelDFS"      "true"
        Option          "DynamicClocks"    "on"
        Option          "ColorTiling"       "on"
        Option          "FBTexPercent"       "95" 
        Option          "XAANoOffscreenPixmaps" "true"
        Option          "AddARGBGLXVisuals"     "true"
EndSection
Section "DRI"
    Mode 0666
Endsection
Section "Extensions"
    Option              "Composite"     "Enable"
Endsection

Notes:

  • [cmang] When following the above instructions, I was unable to get any window borders and window management when starting Compiz. In addition to the above, I had to install the compizconfig-settings-manager package. Then I ran ccsm and made sure that the "Window Decoration" plug-in was enabled. I then had to start compiz with: compiz --replace cpp

Hibernate

[?DamyanIvanov] Hibernate worked for me just fine after I've set up a 256M dedicated SWAP partition. Perhaps the same is possible using swap files too. The only glitch is that I have to quit memory-hungry programs like Iceweasel before attempting hibernate, as otherwise the swap space is not enough. To hibernate, run s2disk as root (from the uswsusp package). If you use gnome-power-manager you can just press the power button (but remember to disable the button action in /etc/acpi/actions/power.sh installed by debian-eeepc-scripts to avoid double prompts).

Troubleshooting

If you have problems with any of the steps above, see our [:DebianEeePC/HowTo/Troubleshooting:Troubleshooting ?HowTo].